- 810.00 KB
- 131页
- 1、本文档共5页,可阅读全部内容。
- 2、本文档内容版权归属内容提供方,所产生的收益全部归内容提供方所有。如果您对本文有版权争议,可选择认领,认领后既往收益都归您。
- 3、本文档由用户上传,本站不保证质量和数量令人满意,可能有诸多瑕疵,付费之前,请仔细先通过免费阅读内容等途径辨别内容交易风险。如存在严重挂羊头卖狗肉之情形,可联系本站下载客服投诉处理。
- 文档侵权举报电话:19940600175。
'预应力混凝土连续梁结构计算书毕业设计一、设计依据1、《城市桥梁设计荷载标准》(CJJ77-98)2、交通部部颁《公路工程技术标准》(JTGB01-2003);3、交通部部颁《公路桥涵设计通用规范》(JTGD60-2004);4、交通部部颁《公路钢筋混凝土及预应力混凝土桥涵设计规范》(JTGD62-2004);5、交通部部颁《公路桥涵地基与基础设计规范》(JTJ024-85);6、交通部部颁《公路工程抗震设计规范》(JTJ004-89);7、交通部部颁《公路桥涵施工技术规范》(JTJ041-2000);8、Dr.Bridge系统--<<桥梁博士>>V3.0版;9、交通部部颁《高速公路交通安全设施设计及施工技术规范》(JTJ074-94);同时参照交通部部颁《公路交通安全设施设计技术规范》(修订征求意见稿)(JTJ074-2003);10、交通部现行的其他《规范》、《规程》、《办法》。二、技术指标1、道路等级:城市次干路-Ⅱ级,按4车道计算;2、计算行车速度30公里/小时;3、全幅桥面宽度:2.5m(护栏)+15m(行车道)+2.5m(护栏)=20m;5、设计荷载:城-A级;6、温度荷载:按《公路桥涵设计通用规范》(JTGD60-2004)4.3.10.3取用a、体系整体升温15度;b、体系整体降温15度;c、梯度温度●顶板顶层处:25℃●顶板顶层以下10cm:6.7℃●顶板顶层以下40cm:0℃7、桥孔布置:4x30+4x30+4x30预应力混凝土连续箱梁桥;130
8、桥面采用双向横坡(由主梁顶板形成);9、本桥位于直线内。按直线桥梁计算。三、材料参数1、混凝土:a、主梁采用C50混凝土:轴心抗压强度标准值fck=32.4Mpa,轴心抗拉强度标准值ftk=2.65Mpa弹性模量Ec=3.45×104Mpa。容重26KN/m3;b、水泥混凝土桥面铺装130cm,容重26KN/m3;c、栏杆底座采用C40混凝土;d、桥墩采用C30混凝土:轴心抗压强度标准值fck=20.1Mpa,轴心抗拉强度标准值ftk=2.01Mpa弹性模量Ec=3.00×104Mpa。容重26KN/m3;2、预应力钢材:15.20预应力钢绞线:标准强度fpk=1860Mpa,弹性模量Ep=1.95×105Mpa。公称面积140mm2,15.20Ⅱ级松弛钢绞线束。张拉控制应力1350Mpa摩阻系数μ=0.14,孔道偏差摩阻系数k=0.0015,一端锚具变形δ=6毫米,松弛率R=0。锚具:预应力钢绞线采用OVM型锚具。3、普通钢筋采用HRB335钢筋。4、伸缩装置:桥台两侧均采用GQF-MZL160型伸缩缝装置,安装宽度120mm。5、支座:待计算后确定。6、基础沉降:基础不均匀沉降按0.01cm计算。四、结构形式及结构尺寸1、主梁:l主梁采用单箱双室断面,梁高1800mm,外悬臂长度为4000mm,桥面横坡2%,由主梁倾斜形成;l标准断面顶板最小厚度为230mm,底板最小厚度210mm,腹板最小厚度500mm;l支点处断面顶板最小厚度为480mm,底板最小厚度460mm;l顶板、底板及腹板厚度变化段长度:3000mm;l按B类构件进行计算2、主梁一般构造图见下图:130
3、主梁钢束布置见设计详图。腹板束采用φs15.20-22预应力钢绞线,底板通长束采用φs15.20-7预应力钢绞线,底板端短束采用φs15.20-3预应力钢绞线。4、墩台形式:柱式墩台5、基础采用桩基础。五、主梁内力计算1.本桥主梁按四跨一联计算,一联长4x30=120m,C50混凝土数量为1525.50m3。l桥面铺装按均布荷载加载:0.13*20*26*1.2=81KN/m(考虑人行道系数1.2)。l活载按城-A级,由Dr.Bridge系统自动计算。l全桥共划分124个单元,125个节点。l结构离散图见下图:l2、33、93、123号节点为竖向支撑,63号节点为固定支撑。1、指定单元截面应力输出********************************************************************************施工阶段内力位移输出********************************************************************************第1施工阶段结构效应阶段支承反力汇总:阶段累计结果:节点号水平力竖向力弯矩20.000e+0006.908e+0030.000e+000330.000e+0001.129e+0040.000e+00063-6.648e-0021.303e+0040.000e+000930.000e+0001.124e+0040.000e+0001230.000e+0006.954e+0030.000e+000阶段永久载结果:节点号水平力竖向力弯矩20.000e+0005.192e+0030.000e+000130
330.000e+0001.379e+0040.000e+00063-8.990e-0101.146e+0040.000e+000930.000e+0001.375e+0040.000e+0001230.000e+0005.230e+0030.000e+000********************************************************************************正常使用阶段内力位移输出********************************************************************************正常使用阶段支承反力汇总:结构重力结果:节点号水平力竖向力弯矩20.000e+0006.908e+0030.000e+000330.000e+0001.129e+0040.000e+00063-6.648e-0021.303e+0040.000e+000930.000e+0001.124e+0040.000e+0001230.000e+0006.954e+0030.000e+000预应力结果:节点号水平力竖向力弯矩20.000e+000-7.581e+0010.000e+000330.000e+0001.161e+0020.000e+00063-1.187e-010-8.070e+0010.000e+000930.000e+0001.166e+0020.000e+0001230.000e+000-7.625e+0010.000e+000汽车MaxM结果:节点号水平力竖向力弯矩20.000e+0000.000e+0000.000e+000330.000e+0000.000e+0000.000e+000630.000e+0000.000e+0000.000e+000930.000e+0000.000e+0000.000e+0001230.000e+0000.000e+0000.000e+000130
汽车MinM结果:节点号水平力竖向力弯矩20.000e+0000.000e+0000.000e+000330.000e+0000.000e+0000.000e+000630.000e+0000.000e+0000.000e+000930.000e+0000.000e+0000.000e+0001230.000e+0000.000e+0000.000e+000汽车MaxQ结果:节点号水平力竖向力弯矩20.000e+0001.975e+0030.000e+000330.000e+0003.288e+0030.000e+000630.000e+0003.158e+0030.000e+000930.000e+0003.282e+0030.000e+0001230.000e+0001.956e+0030.000e+000汽车MinQ结果:节点号水平力竖向力弯矩20.000e+000-1.924e+0020.000e+000330.000e+000-3.183e+0020.000e+000630.000e+000-5.988e+0020.000e+000930.000e+000-3.195e+0020.000e+0001230.000e+000-1.941e+0020.000e+000荷载组合I支承反力组合结果:节点号=2内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力6.908e+0036.908e+0038.239e+0036.441e+0036.908e+0036.908e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=33内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000130
竖向力1.129e+0041.129e+0041.379e+0049.916e+0031.129e+0041.129e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=63内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力-6.648e-002-6.648e-002-6.648e-002-6.648e-002-6.648e-002-6.648e-002竖向力1.303e+0041.303e+0041.584e+0041.136e+0041.303e+0041.303e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=93内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力1.124e+0041.124e+0041.374e+0049.856e+0031.124e+0041.124e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=123内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力6.954e+0036.954e+0038.281e+0036.483e+0036.954e+0036.954e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000荷载组合II支承反力组合结果:节点号=2内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力6.908e+0036.908e+0038.880e+0036.378e+0036.908e+0036.908e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=33内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力1.129e+0041.129e+0041.491e+0049.811e+0031.129e+0041.129e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=63内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小130
水平力-6.648e-002-6.648e-002-6.648e-002-6.648e-002-6.648e-002-6.648e-002竖向力1.303e+0041.303e+0041.692e+0041.115e+0041.303e+0041.303e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=93内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力1.124e+0041.124e+0041.485e+0049.750e+0031.124e+0041.124e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=123内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力6.954e+0036.954e+0038.917e+0036.419e+0036.954e+0036.954e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000荷载组合III支承反力组合结果:节点号=2内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力6.908e+0036.908e+0039.745e+0036.298e+0036.908e+0036.908e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=33内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力1.129e+0041.129e+0041.626e+0049.613e+0031.129e+0041.129e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=63内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力-6.648e-002-6.648e-002-6.648e-002-6.648e-002-6.648e-002-6.648e-002竖向力1.303e+0041.303e+0041.825e+0041.091e+0041.303e+0041.303e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=93130
内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力1.124e+0041.124e+0041.621e+0049.551e+0031.124e+0041.124e+004弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=123内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力6.954e+0036.954e+0039.773e+0036.339e+0036.954e+0036.954e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000********************************************************************************指定单元截面应力输出********************************************************************************第1施工阶段应力结果阶段累计应力:主截面:单元号左上缘左下缘右上缘右下缘11.43e-0141.43e-014-0.2530.9062-0.2530.906-0.1230.7463-0.1230.7460.9840.21740.9840.2172.14-0.18352.14-0.1831.862.3661.862.362.176.6272.176.621.877.8981.877.891.628.791.628.71.878.67101.878.672.328.29112.328.292.757.67122.757.673.147.11130
133.147.113.486.63143.486.633.766.23153.766.233.985.91163.985.914.155.69174.155.694.265.53184.265.534.315.48194.315.484.35.52204.35.524.235.66214.235.664.115.88224.115.884.026.04234.026.044.016.07244.016.074.115.93254.115.934.345.56264.345.564.615.16274.615.164.864.8284.864.84.814.15294.814.154.542.97304.542.974.082.35314.082.353.432.47323.432.472.673.4332.673.43.412.44343.412.444.062.28354.062.284.572.4364.572.44.972.85374.972.855.13.24385.13.244.963.39394.963.394.783.63404.783.634.623.83414.623.834.593.83424.593.834.653.7130
434.653.74.783.47444.783.474.923.22454.923.225.023.06465.023.065.072.97475.072.975.042.99485.042.994.933.14494.933.144.773.36504.773.364.563.66514.563.664.314.02524.314.024.084.33534.084.333.94.54543.94.543.84.65553.84.653.84.6563.84.63.834.56573.834.563.794.61583.794.613.624.21593.624.213.163.77603.163.772.573.67612.573.671.853.87621.853.870.9324.99630.9324.991.853.87641.853.872.573.67652.573.673.163.76663.163.763.634.2673.634.23.84.6683.84.63.834.54693.834.543.814.59703.814.593.814.64713.814.643.914.53723.914.534.094.31130
734.094.314.324744.3244.583.64754.583.644.793.33764.793.334.953.12774.953.125.062.96785.062.965.092.94795.092.945.053.02805.053.024.953.19814.953.194.83.44824.83.444.683.66834.683.664.623.79844.623.794.653.79854.653.794.813.58864.813.584.993.34874.993.345.143.19885.143.1952.818952.814.62.36904.62.364.092.24914.092.243.442.4923.442.42.73.36932.73.363.462.44943.462.444.12.33954.12.334.552.95964.552.954.824.14974.824.144.874.79984.874.794.615.16994.615.164.335.581004.335.584.15.961014.15.963.996.111023.996.113.996.08130
1033.996.084.075.931044.075.934.185.721054.185.724.255.61064.255.64.255.571074.255.574.25.631084.25.634.075.81094.075.83.96.041103.96.043.676.361113.676.363.386.771123.386.773.047.261133.047.262.647.841142.647.842.28.471152.28.471.758.851161.758.851.58.861171.58.861.778.011181.778.012.076.741192.076.741.782.11201.782.12-0.01241212-0.01240.8490.3841220.8490.384-0.2630.918123-0.2630.918-0.2530.906124-0.2530.9061.07e-013-7.02e-014阶段永久载应力:主截面:单元号左上缘左下缘右上缘右下缘100-0.01290.01592-0.01290.01590.0821-0.10130.0821-0.1010.456-0.56240.456-0.5620.975-1.24130
50.975-1.241.41-1.8161.41-1.812.04-2.8972.04-2.892.34-3.4682.34-3.462.71-4.0992.71-4.093.02-4.61103.02-4.613.26-5.04113.26-5.043.45-5.34123.45-5.343.58-5.54133.58-5.543.66-5.65143.66-5.653.67-5.68153.67-5.683.63-5.62163.63-5.623.54-5.47173.54-5.473.36-5.2183.36-5.23.12-4.83193.12-4.832.85-4.4202.85-4.42.51-3.88212.51-3.882.12-3.27222.12-3.271.66-2.57231.66-2.571.16-1.78241.16-1.780.592-0.91250.592-0.91-0.02790.042726-0.02790.0427-0.7021.0727-0.7021.07-1.432.1828-1.432.18-1.742.5229-1.742.52-2.363.1730-2.363.17-2.983.8231-2.983.82-3.654.5232-3.654.52-4.715.8333-4.715.83-3.774.6634-3.774.66-3.24.1130
35-3.24.1-2.693.6236-2.693.62-2.213.1937-2.213.19-1.98338-1.983-1.362.0739-1.362.07-0.8061.2340-0.8061.23-0.3050.46741-0.3050.4670.142-0.217420.142-0.2170.532-0.819430.532-0.8190.866-1.33440.866-1.331.14-1.76451.14-1.761.36-2.1461.36-2.11.53-2.35471.53-2.351.65-2.54481.65-2.541.68-2.59491.68-2.591.65-2.54501.65-2.541.55-2.39511.55-2.391.4-2.16521.4-2.161.2-1.84531.2-1.840.93-1.43540.93-1.430.609-0.933550.609-0.9330.231-0.353560.231-0.353-0.2020.30757-0.2020.307-0.6921.0558-0.6921.05-0.9171.3259-0.9171.32-1.371.8460-1.371.84-1.852.3661-1.852.36-2.362.9262-2.362.92-3.183.9363-3.183.93-2.362.9264-2.362.92-1.842.36130
65-1.842.36-1.371.8466-1.371.84-0.9111.3167-0.9111.31-0.6851.0468-0.6851.04-0.1930.29469-0.1930.2940.241-0.368700.241-0.3680.62-0.95710.62-0.950.943-1.45720.943-1.451.21-1.86731.21-1.861.42-2.19741.42-2.191.57-2.42751.57-2.421.67-2.57761.67-2.571.7-2.62771.7-2.621.67-2.57781.67-2.571.55-2.39791.55-2.391.39-2.14801.39-2.141.17-1.8811.17-1.80.895-1.38820.895-1.380.562-0.865830.562-0.8650.173-0.266840.173-0.266-0.2720.41785-0.2720.417-0.7721.1886-0.7721.18-1.332.0287-1.332.02-1.942.9488-1.942.94-2.183.1489-2.183.14-2.663.5790-2.663.57-3.174.0691-3.174.06-3.734.6292-3.734.62-4.685.7993-4.685.79-3.624.4894-3.624.48-2.963.79130
95-2.963.79-2.333.1496-2.333.14-1.732.4997-1.732.49-1.422.1598-1.422.15-0.6921.0699-0.6921.06-0.0240.0368100-0.0240.03680.589-0.9071010.589-0.9071.15-1.771021.15-1.771.65-2.551031.65-2.552.1-3.241042.1-3.242.48-3.841052.48-3.842.81-4.351062.81-4.353.09-4.771073.09-4.773.32-5.131083.32-5.133.49-5.391093.49-5.393.58-5.531103.58-5.533.61-5.581113.61-5.583.59-5.551123.59-5.553.51-5.421133.51-5.423.37-5.211143.37-5.213.18-4.911153.18-4.912.93-4.471162.93-4.472.61-3.941172.61-3.942.23-3.31182.23-3.31.94-2.741191.94-2.741.31-1.681201.31-1.680.875-1.111210.875-1.110.354-0.4371220.354-0.437-0.02260.0279123-0.02260.0279-0.01290.0159124-0.01290.0159-3.54e-0144.36e-014130
正常使用阶段应力计算结果主截面:结构重力应力结果单元号左上缘左下缘右上缘右下缘11.43e-0141.43e-014-0.2530.9062-0.2530.906-0.1230.7463-0.1230.7460.9840.21740.9840.2172.14-0.18352.14-0.1831.862.3661.862.362.176.6272.176.621.877.8981.877.891.628.791.628.71.878.67101.878.672.328.29112.328.292.757.67122.757.673.147.11133.147.113.486.63143.486.633.766.23153.766.233.985.91163.985.914.155.69174.155.694.265.53184.265.534.315.48194.315.484.35.52204.35.524.235.66214.235.664.115.88224.115.884.026.04234.026.044.016.07244.016.074.115.93254.115.934.345.56264.345.564.615.16130
274.615.164.864.8284.864.84.814.15294.814.154.542.97304.542.974.082.35314.082.353.432.47323.432.472.673.4332.673.43.412.44343.412.444.062.28354.062.284.572.4364.572.44.972.85374.972.855.13.24385.13.244.963.39394.963.394.783.63404.783.634.623.83414.623.834.593.83424.593.834.653.7434.653.74.783.47444.783.474.923.22454.923.225.023.06465.023.065.072.97475.072.975.042.99485.042.994.933.14494.933.144.773.36504.773.364.563.66514.563.664.314.02524.314.024.084.33534.084.333.94.54543.94.543.84.65553.84.653.84.6563.84.63.834.56130
573.834.563.794.61583.794.613.624.21593.624.213.163.77603.163.772.573.67612.573.671.853.87621.853.870.9324.99630.9324.991.853.87641.853.872.573.67652.573.673.163.76663.163.763.634.2673.634.23.84.6683.84.63.834.54693.834.543.814.59703.814.593.814.64713.814.643.914.53723.914.534.094.31734.094.314.324744.3244.583.64754.583.644.793.33764.793.334.953.12774.953.125.062.96785.062.965.092.94795.092.945.053.02805.053.024.953.19814.953.194.83.44824.83.444.683.66834.683.664.623.79844.623.794.653.79854.653.794.813.58864.813.584.993.34130
874.993.345.143.19885.143.1952.818952.814.62.36904.62.364.092.24914.092.243.442.4923.442.42.73.36932.73.363.462.44943.462.444.12.33954.12.334.552.95964.552.954.824.14974.824.144.874.79984.874.794.615.16994.615.164.335.581004.335.584.15.961014.15.963.996.111023.996.113.996.081033.996.084.075.931044.075.934.185.721054.185.724.255.61064.255.64.255.571074.255.574.25.631084.25.634.075.81094.075.83.96.041103.96.043.676.361113.676.363.386.771123.386.773.047.261133.047.262.647.841142.647.842.28.471152.28.471.758.851161.758.851.58.86130
1171.58.861.778.011181.778.012.076.741192.076.741.782.11201.782.12-0.01241212-0.01240.8490.3841220.8490.384-0.2630.91123-0.2630.918-0.2530.906124-0.2530.9061.07e-013-7.02e-014预应力应力结果单元号左上缘左下缘右上缘右下缘1000.00504-0.018720.00504-0.01870.00359-0.017130.00359-0.0171-0.0177-0.01144-0.0177-0.0114-0.0428-0.01825-0.0428-0.0182-0.0233-0.1386-0.0233-0.138-0.00445-0.4047-0.00445-0.4040.0282-0.53980.0282-0.5390.0743-0.71190.0743-0.7110.0894-0.801100.0894-0.8010.0845-0.827110.0845-0.8270.0699-0.79120.0699-0.790.053-0.745130.053-0.7450.0363-0.701140.0363-0.7010.02-0.658150.02-0.6580.00464-0.621160.00464-0.621-0.0101-0.58717-0.0101-0.587-0.0247-0.55918-0.0247-0.559-0.0383-0.53619-0.0383-0.536-0.0499-0.51920-0.0499-0.519-0.061-0.505130
21-0.061-0.505-0.0724-0.49222-0.0724-0.492-0.0889-0.46723-0.0889-0.467-0.112-0.42924-0.112-0.429-0.145-0.36725-0.145-0.367-0.188-0.28326-0.188-0.283-0.236-0.18327-0.236-0.183-0.284-0.081128-0.284-0.0811-0.297-0.020729-0.297-0.0207-0.3110.081830-0.3110.0818-0.3140.13931-0.3140.139-0.3110.16732-0.3110.167-0.3220.18933-0.3220.189-0.3180.17734-0.3180.177-0.3250.16435-0.3250.164-0.3290.1436-0.3290.14-0.3270.099737-0.3270.0997-0.3220.073338-0.3220.0733-0.2870.0062439-0.2870.00624-0.251-0.061240-0.251-0.0612-0.22-0.11141-0.22-0.111-0.198-0.14342-0.198-0.143-0.183-0.16343-0.183-0.163-0.174-0.17244-0.174-0.172-0.168-0.17445-0.168-0.174-0.163-0.17746-0.163-0.177-0.158-0.18147-0.158-0.181-0.15-0.19348-0.15-0.193-0.14-0.21649-0.14-0.216-0.132-0.23650-0.132-0.236-0.124-0.258130
51-0.124-0.258-0.115-0.2852-0.115-0.28-0.111-0.29353-0.111-0.293-0.113-0.29754-0.113-0.297-0.121-0.28755-0.121-0.287-0.139-0.25256-0.139-0.252-0.16-0.20457-0.16-0.204-0.18-0.1658-0.18-0.16-0.182-0.12459-0.182-0.124-0.179-0.069560-0.179-0.0695-0.168-0.040361-0.168-0.0403-0.152-0.025462-0.152-0.0254-0.138-0.030463-0.138-0.0304-0.153-0.02564-0.153-0.025-0.168-0.038965-0.168-0.0389-0.18-0.067266-0.18-0.0672-0.183-0.12167-0.183-0.121-0.18-0.15868-0.18-0.158-0.161-0.20369-0.161-0.203-0.139-0.25270-0.139-0.252-0.121-0.28671-0.121-0.286-0.113-0.29672-0.113-0.296-0.111-0.29273-0.111-0.292-0.115-0.27974-0.115-0.279-0.124-0.25775-0.124-0.257-0.132-0.23576-0.132-0.235-0.141-0.21477-0.141-0.214-0.15-0.19178-0.15-0.191-0.158-0.17979-0.158-0.179-0.164-0.17580-0.164-0.175-0.169-0.172130
81-0.169-0.172-0.174-0.1782-0.174-0.17-0.183-0.16183-0.183-0.161-0.198-0.14284-0.198-0.142-0.22-0.10985-0.22-0.109-0.251-0.058886-0.251-0.0588-0.2870.0075887-0.2870.00758-0.3230.073688-0.3230.0736-0.3270.099589-0.3270.0995-0.3290.1490-0.3290.14-0.3250.16391-0.3250.163-0.3190.17892-0.3190.178-0.3230.18993-0.3230.189-0.3110.16894-0.3110.168-0.3140.14295-0.3140.142-0.3120.085596-0.3120.0855-0.297-0.017297-0.297-0.0172-0.285-0.077998-0.285-0.0779-0.236-0.18299-0.236-0.182-0.187-0.285100-0.187-0.285-0.145-0.368101-0.145-0.368-0.112-0.431102-0.112-0.431-0.0879-0.471103-0.0879-0.471-0.0711-0.497104-0.0711-0.497-0.0595-0.511105-0.0595-0.511-0.0483-0.525106-0.0483-0.525-0.0365-0.542107-0.0365-0.542-0.0227-0.566108-0.0227-0.566-0.00786-0.596109-0.00786-0.5960.00701-0.631100.00701-0.630.0225-0.668130
1110.0225-0.6680.039-0.7111120.039-0.7110.056-0.7571130.056-0.7570.0731-0.8031140.0731-0.8030.0879-0.841150.0879-0.840.0926-0.8131160.0926-0.8130.0769-0.7271170.0769-0.7270.0286-0.561180.0286-0.56-0.00521-0.427119-0.00521-0.427-0.0252-0.12120-0.0252-0.12-0.0409-0.0203121-0.0409-0.0203-0.016-0.0137122-0.016-0.01370.00522-0.01931230.00522-0.01930.00511-0.01891240.00511-0.018900汽车MaxM应力结果单元号左上缘左下缘右上缘右下缘100002000.0258-0.031930.0258-0.03190.138-0.1740.138-0.170.297-0.37650.297-0.3760.433-0.55760.433-0.5570.637-0.90170.637-0.9010.734-1.0980.734-1.090.861-1.390.861-1.30.968-1.48100.968-1.481.06-1.63111.06-1.631.13-1.74121.13-1.741.18-1.83131.18-1.831.23-1.89141.23-1.891.25-1.93130
151.25-1.931.26-1.95161.26-1.951.26-1.94171.26-1.941.24-1.92181.24-1.921.2-1.85191.2-1.851.15-1.78201.15-1.781.09-1.69211.09-1.691.02-1.58221.02-1.580.942-1.45230.942-1.450.85-1.31240.85-1.310.749-1.15250.75-1.150.639-0.979260.639-0.9790.53-0.808270.53-0.8080.429-0.652280.429-0.6520.363-0.524290.363-0.5240.273-0.367300.273-0.3670.186-0.238310.186-0.2380.14-0.173320.14-0.1730.143-0.177330.143-0.1770.124-0.153340.124-0.1540.192-0.245350.192-0.2450.267-0.359360.267-0.3590.364-0.524370.364-0.5240.424-0.641380.424-0.6410.513-0.779390.513-0.780.608-0.928400.608-0.9280.705-1.08410.705-1.080.792-1.22420.792-1.220.867-1.33430.867-1.330.929-1.43440.929-1.430.979-1.51130
450.979-1.511.02-1.56461.02-1.561.04-1.6471.04-1.61.07-1.65481.07-1.651.04-1.61491.04-1.611.02-1.58501.02-1.580.989-1.52510.989-1.520.943-1.45520.943-1.450.884-1.36530.884-1.360.814-1.25540.814-1.250.746-1.14550.746-1.140.654-0.999560.654-0.9990.57-0.867570.57-0.8670.481-0.729580.481-0.7280.427-0.615590.427-0.6150.331-0.446600.332-0.4460.26-0.333610.26-0.3330.23-0.285620.23-0.2850.25-0.31630.25-0.310.231-0.286640.231-0.2860.26-0.333650.26-0.3330.332-0.447660.332-0.4470.419-0.604670.419-0.6040.477-0.721680.477-0.7210.557-0.846690.557-0.8460.641-0.978700.641-0.9780.733-1.12710.733-1.120.814-1.25720.814-1.250.885-1.36730.885-1.360.943-1.45740.943-1.450.989-1.52130
750.989-1.521.02-1.58761.02-1.581.04-1.61771.04-1.611.07-1.65781.07-1.651.04-1.6791.04-1.61.02-1.56801.02-1.560.978-1.51810.978-1.510.928-1.43820.928-1.430.866-1.33830.866-1.330.791-1.21840.791-1.210.704-1.08850.704-1.080.62-0.947860.62-0.9470.526-0.8870.526-0.80.433-0.655880.433-0.6550.369-0.532890.369-0.5320.267-0.36900.267-0.360.191-0.244910.191-0.2450.124-0.154920.124-0.1540.144-0.178930.144-0.1780.14-0.174940.14-0.1740.187-0.239950.186-0.2390.273-0.367960.273-0.3670.364-0.527970.364-0.5270.428-0.649980.428-0.650.528-0.805990.528-0.8050.637-0.9761000.637-0.9760.746-1.151010.746-1.150.846-1.31020.846-1.30.936-1.451030.936-1.451.02-1.571041.02-1.571.09-1.68130
1051.09-1.681.14-1.771061.14-1.771.19-1.841071.19-1.841.23-1.91081.23-1.91.25-1.941091.25-1.941.26-1.941101.26-1.941.24-1.921111.24-1.921.22-1.881121.22-1.881.17-1.811131.17-1.811.12-1.721141.12-1.721.04-1.611151.04-1.610.948-1.451160.948-1.450.837-1.261170.838-1.260.707-1.051180.708-1.050.61-0.8621190.61-0.8630.407-0.5221200.407-0.5220.27-0.3421210.27-0.3420.111-0.1371220.111-0.1370012300001240000汽车MinM应力结果单元号左上缘左下缘右上缘右下缘100-0.07540.09312-0.07540.0931-0.07570.09353-0.07570.0935-0.07790.09614-0.07790.0961-0.08420.1075-0.08420.107-0.08670.1116-0.08670.111-0.1030.1467-0.1030.146-0.1110.1638-0.1110.163-0.1150.174130
9-0.1150.174-0.1330.20310-0.1330.203-0.1540.23911-0.1540.239-0.1760.27112-0.1760.271-0.1970.30513-0.1970.305-0.2180.33714-0.2180.337-0.240.37115-0.240.371-0.2610.40316-0.2610.403-0.2820.43617-0.2820.436-0.3060.47218-0.3060.472-0.3290.50919-0.3290.509-0.350.54120-0.350.541-0.3720.57421-0.3720.574-0.3930.60722-0.3930.607-0.4140.63923-0.4140.639-0.4350.6724-0.4350.67-0.4550.725-0.4550.7-0.4760.72926-0.4760.729-0.5020.76627-0.5020.766-0.5450.82828-0.5450.828-0.5480.79229-0.5480.792-0.5670.76330-0.5670.763-0.6010.76931-0.6010.769-0.6470.80132-0.6470.801-0.831.0333-0.831.03-0.7260.89934-0.7260.899-0.680.8735-0.680.87-0.6470.87136-0.6470.871-0.6310.9137-0.6310.91-0.6310.95438-0.6310.954-0.580.882130
39-0.580.882-0.5480.83740-0.5480.837-0.5280.80941-0.5280.809-0.5060.77842-0.5060.778-0.4840.74543-0.4840.745-0.4620.71144-0.4620.711-0.4390.67645-0.4390.676-0.4170.64246-0.4170.642-0.3940.60747-0.3940.607-0.3660.56348-0.3660.563-0.3620.55749-0.3620.557-0.3760.5850-0.3760.58-0.3910.60251-0.3910.602-0.4060.62552-0.4060.625-0.420.64753-0.420.647-0.4350.66854-0.4350.668-0.4480.68755-0.4480.687-0.4620.70656-0.4620.706-0.4930.7557-0.4930.75-0.5360.81258-0.5360.812-0.5380.77659-0.5380.776-0.5560.74760-0.5560.747-0.5880.75361-0.5880.753-0.6330.78362-0.6330.783-0.7290.90363-0.7290.903-0.6330.78464-0.6330.784-0.5880.75365-0.5880.753-0.5560.74866-0.5560.748-0.5390.77667-0.5390.776-0.5370.81268-0.5370.812-0.4940.751130
69-0.4940.751-0.4620.70670-0.4620.706-0.4480.68771-0.4480.687-0.4340.66872-0.4340.668-0.420.64673-0.420.646-0.4050.62474-0.4050.624-0.390.60175-0.390.601-0.3760.57876-0.3760.578-0.3610.55577-0.3610.555-0.3630.55978-0.3630.559-0.3910.60279-0.3910.602-0.4130.63680-0.4130.636-0.4350.6781-0.4350.67-0.4580.70582-0.4580.705-0.480.73883-0.480.738-0.5010.7784-0.5010.77-0.5230.80185-0.5230.801-0.5430.82986-0.5430.829-0.5750.87387-0.5750.873-0.6250.94588-0.6250.945-0.6250.90289-0.6250.902-0.6420.86390-0.6420.863-0.6740.86391-0.6740.863-0.7210.89292-0.7210.892-0.8251.0293-0.8251.02-0.6460.894-0.6460.8-0.60.76895-0.60.768-0.5660.76296-0.5660.762-0.5470.79197-0.5470.791-0.5450.82898-0.5450.828-0.5030.767130
99-0.5030.767-0.4770.73100-0.4770.73-0.4560.701101-0.4560.701-0.4350.671102-0.4350.671-0.4140.64103-0.4140.64-0.3930.608104-0.3930.608-0.3720.575105-0.3720.575-0.350.541106-0.350.541-0.3290.508107-0.3290.508-0.3050.472108-0.3050.472-0.2820.435109-0.2820.435-0.260.402110-0.260.402-0.2390.369111-0.2390.369-0.2170.336112-0.2170.336-0.1960.302113-0.1960.302-0.1740.269114-0.1740.269-0.1530.236115-0.1530.236-0.1330.203116-0.1330.203-0.1290.194117-0.1290.194-0.1250.184118-0.1250.184-0.1170.166119-0.1170.166-0.09950.128120-0.09950.128-0.09760.124121-0.09760.124-0.09140.113122-0.09140.113-0.08970.111123-0.08970.111-0.07540.0931124-0.07540.093100汽车MaxQ应力结果单元号左上缘左下缘右上缘右下缘100-0.07540.09312-0.0007960.000982-0.002440.00302130
30.0246-0.0303-0.01270.015740.134-0.165-0.02520.03250.286-0.3630.284-0.36560.413-0.530.421-0.59670.599-0.8480.488-0.72280.687-1.020.578-0.8790.795-1.20.656-1100.883-1.350.721-1.11110.95-1.470.777-1.2121-1.550.821-1.27131.04-1.60.866-1.34141.06-1.640.89-1.38151.07-1.650.902-1.39161.06-1.640.901-1.39171.04-1.610.88-1.36181.01-1.570.877-1.36190.97-1.50.838-1.3200.922-1.430.786-1.22210.866-1.340.704-1.09220.805-1.240.631-0.974230.739-1.140.546-0.842240.671-1.030.452-0.695250.601-0.9240.348-0.534260.529-0.810.239-0.364270.457-0.6970.12-0.183280.385-0.5840.0539-0.0779290.335-0.484-0.06730.0907300.249-0.335-0.1820.233310.178-0.227-0.2940.364320.0674-0.0834-0.4350.538130
33-0.4640.5740.116-0.14434-0.3070.380.102-0.1335-0.1910.2450.0883-0.11936-0.07470.10.0766-0.11370.0458-0.06610.372-0.563380.111-0.1680.432-0.657390.23-0.350.493-0.753400.333-0.5080.548-0.84410.429-0.6570.598-0.919420.514-0.7890.642-0.988430.587-0.9030.703-1.08440.647-0.9960.735-1.13450.695-1.070.759-1.17460.732-1.130.773-1.19470.757-1.170.759-1.17480.773-1.190.763-1.18490.771-1.190.74-1.14500.759-1.170.705-1.09510.738-1.140.659-1.01520.709-1.090.6-0.923530.672-1.040.53-0.814540.633-0.9720.448-0.687550.587-0.90.355-0.543560.538-0.8210.253-0.385570.485-0.7370.141-0.214580.157-0.2380.0784-0.113590.163-0.236-0.0390.0524600.178-0.239-0.1510.193610.194-0.248-0.2620.324620.213-0.263-0.4310.533130
63-0.4170.5160.213-0.26364-0.2750.3410.194-0.24865-0.1650.2110.178-0.23966-0.05280.0710.163-0.236670.0636-0.09180.157-0.238680.127-0.1920.485-0.738690.239-0.3630.538-0.822700.341-0.5210.588-0.902710.433-0.6640.634-0.974720.515-0.7910.674-1.04730.585-0.90.73-1.12740.643-0.990.759-1.17750.689-1.060.78-1.2760.723-1.110.791-1.22770.746-1.150.774-1.19780.759-1.170.775-1.19790.754-1.160.75-1.15800.739-1.140.713-1.1810.715-1.10.664-1.02820.682-1.050.603-0.928830.642-0.9870.53-0.814840.597-0.9180.445-0.681850.547-0.8390.348-0.532860.493-0.7530.246-0.374870.432-0.6570.127-0.193880.372-0.5630.062-0.0894890.0774-0.112-0.05950.08900.0891-0.12-0.1760.226910.102-0.131-0.2920.362920.117-0.145-0.4690.58130
93-0.4390.5430.072-0.089194-0.2980.3690.178-0.22895-0.1860.2380.25-0.33796-0.07150.09630.336-0.485970.0492-0.07110.386-0.586980.116-0.1750.458-0.698990.232-0.3530.53-0.8121000.342-0.5250.602-0.9251010.445-0.6850.672-1.041020.54-0.8320.739-1.141030.623-0.9620.826-1.281040.695-1.070.887-1.371050.757-1.170.941-1.451060.807-1.250.988-1.531070.844-1.311.02-1.581080.872-1.351.04-1.611090.885-1.371.06-1.641100.884-1.371.06-1.651110.871-1.351.05-1.631120.845-1.311.03-1.591130.811-1.250.994-1.541140.766-1.180.939-1.451150.709-1.10.869-1.331160.642-0.980.778-1.171170.563-0.8470.667-0.9871180.471-0.6970.58-0.821190.405-0.5720.393-0.5051200.268-0.3450.264-0.334121-0.02370.03010.11-0.135122-0.01060.0131-0.001190.00147130
123-0.08980.11100124-0.004410.0054500汽车MinQ应力结果单元号左上缘左下缘右上缘右下缘100002000.025-0.03083-0.002490.003080.134-0.1654-0.01270.01570.286-0.3635-0.02520.0320.413-0.5360.284-0.3650.599-0.84870.422-0.5960.687-1.0280.488-0.7220.795-1.290.578-0.870.883-1.35100.656-10.951-1.47110.721-1.111-1.55120.777-1.21.04-1.6130.821-1.271.06-1.64140.866-1.341.07-1.65150.89-1.381.06-1.64160.902-1.391.04-1.61170.902-1.391.01-1.57180.881-1.360.97-1.5190.879-1.360.922-1.43200.838-1.30.867-1.34210.767-1.190.805-1.24220.705-1.090.739-1.14230.631-0.9750.672-1.04240.547-0.8440.601-0.924250.454-0.6980.529-0.811260.351-0.5380.457-0.697130
270.241-0.3680.385-0.584280.12-0.1830.335-0.484290.0539-0.07790.249-0.33630-0.06740.09070.178-0.22731-0.1820.2330.0683-0.084632-0.2940.3640.0723-0.0895330.143-0.177-0.3070.38340.116-0.144-0.1910.245350.102-0.13-0.07460.1360.0883-0.1190.0459-0.0662370.0766-0.1110.111-0.168380.372-0.5630.23-0.35390.433-0.6570.333-0.508400.494-0.7540.429-0.657410.548-0.840.514-0.79420.598-0.9190.587-0.903430.642-0.9890.647-0.997440.703-1.080.695-1.07450.735-1.130.732-1.13460.759-1.170.757-1.17470.773-1.190.773-1.19480.794-1.220.771-1.19490.763-1.180.759-1.17500.74-1.140.738-1.14510.705-1.090.709-1.09520.659-1.010.673-1.04530.6-0.9230.633-0.972540.53-0.8140.588-0.901550.448-0.6870.538-0.821560.355-0.5430.485-0.737130
570.253-0.3850.157-0.238580.142-0.2150.163-0.236590.0784-0.1130.178-0.23960-0.0390.05250.195-0.24961-0.1510.1930.213-0.26362-0.2620.3240.249-0.308630.248-0.307-0.2750.341640.213-0.263-0.1650.211650.194-0.248-0.05280.071660.178-0.2390.0637-0.0919670.163-0.2360.127-0.192680.157-0.2380.239-0.363690.486-0.7380.341-0.521700.538-0.8220.433-0.664710.589-0.9020.515-0.791720.634-0.9740.585-0.9730.674-1.040.643-0.99740.73-1.120.689-1.06750.759-1.170.723-1.11760.78-1.20.746-1.15770.791-1.220.759-1.17780.81-1.250.754-1.16790.775-1.190.739-1.14800.75-1.150.715-1.1810.713-1.10.682-1.05820.664-1.020.642-0.988830.603-0.9280.597-0.918840.53-0.8140.547-0.839850.445-0.6810.493-0.753860.348-0.5320.432-0.657130
870.246-0.3740.372-0.563880.127-0.1930.0775-0.112890.062-0.08940.0892-0.1290-0.05950.08010.102-0.13191-0.1760.2260.117-0.14592-0.2920.3620.144-0.178930.078-0.0965-0.2980.369940.0729-0.0903-0.1860.238950.179-0.229-0.07150.0963960.25-0.3370.0493-0.0712970.336-0.4850.116-0.176980.386-0.5860.237-0.361990.458-0.6980.344-0.5281000.53-0.8120.447-0.6881010.602-0.9250.54-0.8331020.672-1.040.624-0.9641030.739-1.140.697-1.081040.826-1.280.757-1.171050.887-1.370.808-1.251060.941-1.450.845-1.311070.988-1.530.872-1.351081.02-1.580.886-1.371091.04-1.610.884-1.371101.06-1.640.871-1.351111.06-1.650.845-1.311121.05-1.630.811-1.251131.03-1.590.766-1.181140.994-1.540.709-1.11150.939-1.450.642-0.981160.869-1.330.563-0.847130
1170.778-1.170.471-0.6971180.667-0.9870.405-0.5721190.58-0.820.268-0.3451200.393-0.505-0.02370.03011210.264-0.334-0.01060.01311220.11-0.1350012300-0.07540.09311240000使用阶段荷载组合1应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉1100000.149-0.14912-0.248-0.2830.9440.8880.944-0.28322-0.248-0.2830.9440.8882.54-2.2123-0.11-0.1540.7840.7162.38-2.0733-0.11-0.1540.7840.7162.37-2.06341.040.9350.2560.1341.5-0.914441.040.9350.2560.1341.5-0.914452.262.06-0.139-0.3612.26-0.361552.262.06-0.139-0.3612.26-0.361562.041.82.41.982.4-0.159662.041.82.41.982.4-0.16672.442.126.685.846.68-0.519772.442.126.685.846.68-0.519782.211.827.966.897.96-0.281882.211.827.966.897.96-0.281892.061.578.777.448.77-0.0182992.061.578.777.448.77-0.01829102.371.828.767.258.76-0.22810102.371.828.767.258.76-0.228130
10112.852.258.46.788.4-0.38911112.852.258.46.788.4-0.38911123.32.687.796.147.79-0.37412123.32.687.796.147.79-0.37412133.73.067.245.597.24-0.29313133.73.067.245.597.24-0.29313144.033.386.775.136.77-0.2214144.033.386.775.136.77-0.2214154.313.656.394.756.39-0.15715154.313.656.394.756.39-0.15715164.523.876.094.476.09-0.10316164.523.876.094.476.09-0.10316174.684.015.874.285.87-0.059317174.684.015.874.285.87-0.059317184.794.15.744.165.74-0.024818184.794.15.744.165.74-0.024818194.824.135.74.165.7-0.0079719194.824.135.74.165.7-0.0079519204.794.15.764.255.76-0.029420204.794.15.764.255.76-0.029420214.6945.914.445.91-0.063821214.6945.914.445.91-0.062521224.543.866.144.726.14-0.071922224.543.866.144.726.14-0.071922234.423.756.324.966.32-0.046223234.423.756.324.966.32-0.046123244.383.716.365.096.36-0.012724244.383.716.365.096.36-0.012724254.433.776.235.086.23-0.058825254.433.776.235.086.23-0.0588130
25264.613.955.884.875.88-0.12626264.613.955.884.875.88-0.12626274.834.155.494.645.49-0.1327274.834.155.494.645.49-0.1327285.044.345.164.455.16-0.099628285.044.345.164.455.16-0.099628294.964.274.493.914.96-0.049229294.964.274.493.914.96-0.049229304.653.983.392.814.65-0.072630304.653.983.392.814.65-0.072630314.163.52.842.254.16-0.31931314.163.52.842.254.16-0.31931323.492.8332.43.62-0.68532323.492.8332.43.62-0.68532332.731.974.053.324.22-1.0233332.731.974.053.324.2-1.0633343.472.773.012.373.64-0.7334343.472.773.012.373.64-0.7334354.143.432.832.184.14-0.36935354.143.432.832.184.14-0.36935364.683.962.932.254.68-0.15536364.683.962.932.254.68-0.15536375.124.373.352.635.12-0.036337375.124.373.352.635.12-0.036337385.284.513.732.975.28-0.02338385.284.513.732.975.28-0.022838395.184.423.783.065.18-0.07339395.184.423.783.065.18-0.072639405.034.293.993.185.03-0.088740405.034.293.993.185.03-0.0887130
40414.924.174.183.274.92-0.033941414.924.174.183.274.92-0.034241424.934.174.173.184.93-0.032342424.934.174.173.184.93-0.032342435.024.264.022.975.02-0.075343435.024.264.022.975.02-0.075343445.174.43.782.695.17-0.10544445.174.43.782.695.17-0.10544455.344.563.522.415.34-0.090145455.344.563.522.415.34-0.090145465.464.683.342.215.46-0.045446465.464.683.342.215.46-0.045446475.514.743.242.115.51-0.015447475.514.743.242.115.51-0.015447485.54.733.242.15.5-0.028248485.54.733.242.15.5-0.029448495.374.633.392.245.37-0.077449495.374.633.392.245.37-0.077449505.214.483.612.455.21-0.13150505.214.483.612.455.21-0.13150514.984.273.932.754.98-0.19751514.984.273.932.754.98-0.19751524.714.024.293.124.71-0.21852524.714.024.293.124.71-0.21852534.453.794.613.454.61-0.18253534.453.794.613.454.61-0.18253544.253.64.833.714.83-0.12154544.253.64.833.714.83-0.12154554.123.494.953.874.95-0.048655554.123.494.953.874.95-0.0486130
55564.083.474.93.924.9-0.018456564.083.474.93.924.9-0.018456574.073.464.883.984.88-0.031957574.073.464.883.984.88-0.031957583.993.384.964.144.96-0.09158583.993.384.964.144.96-0.09158593.83.214.543.824.54-0.15659593.83.214.543.824.54-0.15659603.32.744.093.54.09-0.32560603.32.744.093.54.09-0.32560612.682.1543.484-0.5761612.682.1543.484-0.5761621.951.424.213.714.21-0.93362621.951.424.213.714.21-0.93362631.040.4765.394.815.39-1.2563631.040.4765.394.815.39-1.2563641.951.424.213.714.21-0.93264641.951.424.213.714.21-0.93264652.692.1543.484-0.56965652.692.1543.484-0.56965663.32.744.093.54.09-0.32566663.32.744.093.54.09-0.32566673.813.224.543.814.54-0.15667673.813.224.543.814.54-0.156676843.394.954.134.95-0.0909686843.394.954.134.95-0.090968694.073.464.873.984.87-0.031969694.073.464.873.984.87-0.031969704.083.484.893.924.89-0.018470704.083.484.893.924.89-0.0184130
70714.123.54.933.874.93-0.048671714.123.54.933.874.93-0.048671724.263.614.823.74.82-0.12172724.263.614.823.74.82-0.12172734.473.84.593.434.59-0.18273734.473.84.593.434.59-0.18273744.724.034.273.14.72-0.21974744.724.034.273.14.72-0.219747554.283.92.735-0.198757554.283.92.735-0.19875765.234.493.592.435.23-0.13276765.234.493.592.435.23-0.13276775.394.653.362.225.39-0.077777775.394.653.362.225.39-0.077777785.524.753.212.075.52-0.029178785.524.753.212.075.52-0.029178795.534.763.212.085.53-0.015479795.534.763.212.085.53-0.015479805.484.73.32.185.48-0.045280805.484.73.32.185.48-0.045280815.364.593.482.385.36-0.0981815.364.593.482.385.36-0.0981825.194.433.742.665.19-0.10482825.194.433.742.665.19-0.10482835.054.293.982.945.05-0.075383835.054.293.982.945.05-0.075383844.954.24.123.144.95-0.032284844.954.24.123.144.95-0.032284854.954.24.133.234.95-0.034985854.954.24.133.234.95-0.0349130
85865.064.323.943.135.06-0.089986865.064.323.943.135.06-0.089986875.214.463.733.015.21-0.074187875.214.463.733.015.21-0.074187885.324.543.682.925.32-0.023688885.324.543.682.925.32-0.023588895.154.43.32.585.15-0.036389895.154.43.32.585.15-0.036389904.713.992.882.214.71-0.15590904.713.992.882.214.71-0.15590914.173.462.792.144.17-0.3791914.173.462.792.144.17-0.3791923.52.82.972.333.64-0.7392923.52.82.972.333.64-0.7392932.762.014.013.284.18-1.0593932.762.014.013.284.19-193943.522.852.972.373.6-0.67394943.522.852.972.373.6-0.67394954.183.522.812.234.18-0.30995954.183.522.812.234.18-0.30995964.673.993.372.794.67-0.067496964.673.993.372.794.67-0.067496974.974.284.483.94.97-0.053497974.974.284.483.94.97-0.053297985.054.345.144.445.14-0.10598985.054.345.144.445.14-0.10598994.834.155.494.655.49-0.13699994.834.155.494.655.49-0.136991004.63.945.894.885.89-0.1321001004.63.945.894.885.89-0.132130
1001014.413.756.265.116.26-0.06331011014.413.756.265.116.26-0.06331011024.353.696.45.136.4-0.01051021024.353.696.45.136.4-0.01051021034.393.726.3656.36-0.04181031034.393.726.3656.36-0.04181031044.53.836.194.776.19-0.06651041044.53.836.194.776.19-0.06651041054.643.965.974.55.97-0.05741051054.643.965.974.55.97-0.05741051064.734.045.834.335.83-0.02511061064.734.045.834.335.83-0.02521061074.764.075.794.255.79-0.006591071074.764.075.794.255.79-0.006591071084.724.045.844.265.84-0.0281081084.724.045.844.265.84-0.0281081094.63.945.994.385.99-0.06371091094.63.945.994.385.99-0.06371091104.443.796.214.586.21-0.1081101104.443.796.214.586.21-0.1081101114.223.566.524.886.52-0.1631111114.223.566.524.886.52-0.1631111123.943.296.925.276.92-0.2281121123.943.296.925.276.92-0.2281121133.592.957.395.747.39-0.3021131133.592.957.395.747.39-0.3021131143.182.567.956.317.95-0.3841141143.182.567.956.317.95-0.3841141152.732.138.576.958.57-0.3991151152.732.138.576.958.57-0.399130
1151162.241.698.947.428.94-0.2361161162.241.698.947.428.94-0.2361161171.931.458.947.68.94-0.01311171171.931.458.947.68.94-0.01311171182.11.728.097.018.09-0.2921181182.11.728.097.018.09-0.2921181192.332.026.815.956.81-0.5111191192.332.026.815.956.81-0.5111191201.951.712.151.762.15-0.1081201201.951.712.151.762.15-0.1081201212.111.920.0383-0.1772.11-0.1771211212.111.920.0383-0.1772.11-0.1771211220.8970.7970.4290.3121.53-0.9191221220.8970.7970.4290.3121.53-0.919122123-0.257-0.2990.9620.8992.41-2.08123123-0.257-0.2990.9620.8990.962-0.299123124-0.248-0.2830.9430.8870.943-0.283124124-0.248-0.2830.9430.8870.943-0.28312412500000.141-0.141使用阶段荷载组合2应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉115.7700.33905.77-0.764125.52-0.3061.310.8885.52-0.754225.52-0.3061.310.8885.52-2.76235.68-0.1831.150.6975.68-2.62335.68-0.1831.150.6975.68-2.61346.910.8780.640.03586.91-1.44446.910.8780.640.03586.91-1.44458.21.960.264-0.5838.2-0.583130
558.21.960.264-0.5838.2-0.583568.11.662.831.658.1-0.224668.11.572.830.8158.1-0.225678.531.887.193.388.53-0.593778.531.887.193.388.53-0.593788.371.678.53.948.5-0.341888.371.678.53.948.5-0.341898.331.499.344.059.34-0.093998.331.499.344.059.34-0.0939108.761.699.363.629.36-0.44810108.761.699.363.629.36-0.44810119.342.039.032.999.34-0.69211119.342.039.032.999.34-0.69211129.892.358.512.269.89-0.67112129.892.358.512.269.89-0.671121310.42.628.051.6310.4-0.56131310.42.628.051.6310.4-0.56131410.82.847.671.0910.8-0.454141410.82.847.671.0910.8-0.454141511.237.370.65811.2-0.353151511.237.370.65811.2-0.354151611.53.117.160.3211.5-0.262161611.53.117.160.3211.5-0.262161711.73.147.030.082311.7-0.181171711.73.147.030.082211.7-0.181171811.93.126.99-0.078611.9-0.109181811.93.126.99-0.078711.9-0.1091819123.027.05-0.10912-0.0541919123.027.05-0.10912-0.0541920122.887.19-0.040212-0.0969130
2020122.887.19-0.040312-0.09692021122.687.430.13212-0.1552121122.687.430.13212-0.151212211.92.437.750.40211.9-0.168222211.92.437.750.40211.9-0.168222311.92.198.010.67611.9-0.132232311.92.198.010.67611.9-0.131232411.81.998.140.89211.8-0.0724242411.81.998.140.89111.8-0.0724242511.91.868.091.0311.9-0.158252511.91.868.091.0311.9-0.158252612.21.817.811.0312.2-0.268262612.21.817.811.0312.2-0.268262712.41.777.51.0412.4-0.282272712.41.777.51.0412.4-0.282272812.71.77.251.0912.7-0.247282812.71.77.251.0912.7-0.247282912.61.66.450.98912.6-0.159292912.61.66.450.98912.6-0.159293012.21.275.180.56512.2-0.191303012.21.275.180.56512.2-0.191303111.70.764.530.4611.7-0.505313111.70.764.530.4611.7-0.505313211.10.07244.660.83511.1-0.904323211.10.07244.660.83511.1-0.904323310.4-0.9585.851.7410.4-1.26333310.4-0.9585.851.7410.4-1.39333411.10.02774.630.89711.1-1.04343411.10.02774.630.89711.1-1.04343511.70.7364.420.54211.7-0.647130
353511.70.7364.420.54211.7-0.647353612.11.314.530.35712.1-0.383363612.11.314.530.35712.1-0.383363712.61.785.010.3212.6-0.194373712.61.785.010.3212.6-0.194373812.71.955.460.35912.7-0.191383812.71.955.460.35912.7-0.19383912.62.145.330.35712.6-0.316393912.62.145.330.35712.6-0.314394012.32.255.390.34612.3-0.334404012.32.255.390.34612.3-0.334404112.22.335.490.28412.2-0.193414112.22.335.490.28412.2-0.195414212.22.55.380.11312.2-0.176424212.22.55.380.11312.2-0.176424312.22.725.13-0.11912.2-0.255434312.22.725.13-0.11912.2-0.255434412.32.974.78-0.38112.3-0.301444412.32.974.78-0.38112.3-0.301444512.53.24.46-0.65712.5-0.276454512.53.24.46-0.65712.5-0.276454612.63.334.29-0.91212.6-0.196464612.63.334.29-0.91212.6-0.196464712.73.44.2-1.0612.7-0.13474712.73.44.2-1.0612.7-0.13474812.63.424.21-1.1412.6-0.197484812.63.424.21-1.1412.6-0.204484912.53.334.38-1.0312.5-0.299494912.53.334.38-1.0312.5-0.299495012.43.194.64-0.84712.4-0.399130
505012.43.194.64-0.84712.4-0.399505112.22.935.06-0.63912.2-0.506515112.22.935.06-0.63912.2-0.506515211.92.625.56-0.38211.9-0.534525211.92.625.56-0.38211.9-0.534525311.72.36-0.12311.7-0.473535311.72.36-0.12211.7-0.473535411.62.026.350.11111.6-0.396545411.62.026.350.11111.6-0.396545511.51.786.590.2911.5-0.259555511.51.786.590.2911.5-0.259555611.51.66.670.42111.5-0.185565611.51.66.670.42111.5-0.185565711.51.386.810.53611.5-0.226575711.51.386.810.53611.5-0.226575811.51.097.070.74511.5-0.356585811.51.097.070.74511.5-0.356585911.30.916.550.76611.3-0.464595911.30.916.550.76611.3-0.464596010.80.4225.990.91610.8-0.697606010.80.4225.990.91610.8-0.697606110.2-0.1865.851.1810.2-0.987616110.2-0.1865.851.1810.2-0.98661629.56-0.9286.081.589.56-1.3662629.56-0.9286.081.589.56-1.3662638.76-27.432.538.76-1.7163638.76-27.432.538.76-1.7263649.56-0.9276.081.589.56-1.3664649.56-0.9276.081.589.56-1.36646510.2-0.1845.851.1810.2-0.984130
656510.2-0.1845.851.1810.2-0.984656610.80.4265.990.91410.8-0.695666610.80.4265.990.91410.8-0.695666711.30.9166.540.76911.3-0.462676711.30.9166.540.76911.3-0.462676811.51.17.060.74311.5-0.354686811.51.17.060.74311.5-0.354686911.51.396.80.54211.5-0.225696911.51.396.80.54211.5-0.225697011.51.616.660.42511.5-0.184707011.51.616.660.42511.5-0.184707111.51.796.580.29411.5-0.258717111.51.796.580.29411.5-0.258717211.62.036.340.098311.6-0.395727211.62.036.340.098311.6-0.395727311.82.325.98-0.13811.8-0.472737311.82.325.98-0.13811.8-0.4727374122.635.53-0.412-0.5347474122.635.53-0.412-0.534747512.22.955.03-0.65812.2-0.506757512.22.955.03-0.65812.2-0.506757612.43.24.61-0.8712.4-0.399767612.43.24.61-0.87112.4-0.399767712.53.354.36-1.0612.5-0.299777712.53.354.36-1.0612.5-0.299777812.73.444.18-1.1712.7-0.201787812.73.444.18-1.1712.7-0.201787912.73.434.17-1.112.7-0.131797912.73.434.17-1.112.7-0.131798012.63.354.25-0.94512.6-0.198130
808012.63.354.25-0.94512.6-0.198808112.53.224.42-0.69112.5-0.277818112.53.224.42-0.69112.5-0.277818212.32.994.75-0.41912.3-0.303828212.32.994.75-0.41912.3-0.303828312.22.745.09-0.16112.2-0.257838312.22.745.09-0.16112.2-0.257838412.22.525.340.067712.2-0.177848412.22.525.340.067712.2-0.177848512.22.365.450.23712.2-0.199858512.22.365.450.23712.2-0.199858612.42.285.350.28412.4-0.34868612.42.285.350.28412.4-0.34868712.62.175.290.28812.6-0.322878712.62.175.290.28812.6-0.322878812.81.985.420.29412.8-0.196888812.81.985.420.29412.8-0.196888912.61.814.970.26212.6-0.196898912.61.814.970.26212.6-0.196899012.21.344.490.30812.2-0.385909012.21.344.490.30812.2-0.385909111.70.7664.380.49611.7-0.65919111.70.7664.380.49611.7-0.65919211.10.05664.60.85211.1-1.04929211.10.05664.60.85211.1-1.04929310.5-0.9275.811.6910.5-1.39939310.5-0.9275.811.6910.5-1.25939411.20.09324.640.79811.2-0.891949411.20.09324.640.79811.2-0.891949511.80.7754.520.42811.8-0.494130
959511.80.7754.520.42811.8-0.494959612.21.285.170.53912.2-0.183969612.21.285.170.53812.2-0.183969712.61.616.450.9712.6-0.169979712.61.616.450.9712.6-0.168979812.71.77.251.0712.7-0.258989812.71.77.251.0712.7-0.258989912.41.777.511.0412.4-0.293999912.41.777.511.0412.4-0.2939910012.21.87.821.0412.2-0.27810010012.21.87.821.0412.2-0.27810010111.91.848.121.0511.9-0.16610110111.91.848.121.0511.9-0.16610110211.81.978.180.92511.8-0.06710210211.81.978.180.92511.8-0.06710210311.82.168.060.71911.8-0.12410310311.82.168.060.71911.8-0.12410310411.92.397.80.45611.9-0.1610410411.92.397.80.45611.9-0.16104105122.637.490.19912-0.143105105122.637.490.19912-0.143105106122.837.270.039912-0.088106106122.837.270.039812-0.08810610711.92.977.13-0.015711.9-0.059910710711.92.977.13-0.015711.9-0.059910710811.83.057.090.028411.8-0.11710810811.83.057.090.028411.8-0.11710810911.63.077.140.18811.6-0.1910910911.63.077.140.18811.6-0.1910911011.43.037.280.43911.4-0.272130
11011011.43.037.280.43911.4-0.27211011111.12.927.50.79111.1-0.36511111111.12.927.50.79111.1-0.36511111210.72.757.811.2410.7-0.46611211210.72.757.811.2410.7-0.46611211310.32.538.21.7910.3-0.57311311310.32.538.21.7910.3-0.5731131149.772.258.672.449.77-0.6841141149.772.258.672.449.77-0.6841141159.21.929.23.189.2-0.7061151159.21.929.23.189.2-0.7061151168.611.589.533.89.53-0.4591161168.611.589.533.89.53-0.4591161178.191.379.514.239.51-0.08081171178.191.379.514.239.51-0.08081171188.241.578.644.098.64-0.3531181188.241.578.644.098.64-0.3531181198.411.787.323.528.41-0.5841191198.411.787.323.528.41-0.5841191207.991.482.580.6837.99-0.1661201207.991.482.580.6837.99-0.1661201218.031.590.444-0.68.03-0.4421211218.031.590.444-0.68.03-0.4421211226.750.6420.8150.06776.75-1.441221226.750.6420.8150.06776.75-1.441221235.51-0.2771.330.7215.51-2.641231235.51-0.2781.330.7215.51-0.7651231245.52-0.2581.310.7095.52-0.7541241245.52-0.2581.310.7095.52-0.7541241255.77-2.49e-0140.3392.64e-0145.77-0.764130
使用阶段荷载组合3应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉117.2100.42407.21-0.957126.96-0.341.440.8886.96-0.961226.96-0.341.440.8886.96-3.08237.13-0.2171.280.6847.13-2.93337.13-0.2171.280.6847.13-2.92348.420.8430.762-0.03438.42-1.74448.420.8430.762-0.03438.42-1.74459.761.920.38-0.7389.76-0.751559.761.920.38-0.7389.76-0.751569.731.622.941.429.73-0.243669.731.622.941.429.73-0.2446710.21.867.34.9110.2-0.627710.21.867.34.9110.2-0.627810.11.528.625.7610.1-0.3658810.11.528.625.7610.1-0.3658910.11.229.456.0710.1-0.1729910.11.229.456.0710.1-0.17291010.61.49.465.6610.6-0.607101010.61.49.465.6610.6-0.607101111.21.779.144.9911.2-0.892111111.21.779.144.9911.2-0.892111211.82.138.634.1311.8-0.86121211.82.138.634.1311.8-0.86121312.32.448.193.3812.3-0.729131312.32.448.193.3812.3-0.729131412.82.717.822.7312.8-0.602141412.82.717.822.7312.8-0.602130
141513.22.917.542.1913.2-0.481151513.22.917.542.1913.2-0.481151613.53.067.341.7613.5-0.367161613.53.067.341.7613.5-0.367161713.73.147.231.4413.7-0.269171713.73.147.231.4413.7-0.269171813.93.167.21.1913.9-0.177181813.93.167.21.1913.9-0.1771819143.117.281.0914-0.1061919143.117.281.0914-0.1061920143.017.431.114-0.1722020143.017.431.114-0.1722021142.857.691.2214-0.2512121142.857.691.2214-0.244212213.92.658.021.4413.9-0.271222213.92.658.021.4413.9-0.27222313.82.478.31.6513.8-0.23232313.82.478.31.6513.8-0.229232413.72.378.441.7613.7-0.154242413.72.378.441.7613.7-0.154242513.82.368.41.7513.8-0.195252513.82.368.41.7513.8-0.1942526142.478.131.5514-0.3242626142.478.131.5514-0.324262714.22.617.841.3414.2-0.342272714.22.617.841.3414.2-0.342272814.42.717.621.1414.4-0.301282814.42.717.621.1414.4-0.301282914.32.676.810.91514.3-0.198292914.32.676.810.91514.3-0.198130
293013.92.395.520.21213.9-0.334303013.92.395.520.21213.9-0.334303113.41.94.88-0.07513.4-0.723313113.41.94.88-0.07513.4-0.723313212.81.25.020.22212.8-1.14323212.81.25.020.22212.8-1.14323312.10.1436.311.0412.1-1.54333312.10.1436.311.0412.1-1.64333412.71.145.040.2512.7-1.26343412.71.145.040.24912.7-1.26343513.41.884.81-0.080113.4-0.852353513.41.884.81-0.079913.4-0.852353613.92.474.92-0.21413.9-0.564363613.92.474.92-0.21413.9-0.564363714.32.935.42-0.17714.3-0.342373714.32.935.42-0.17814.3-0.342373814.53.085.89-0.094214.5-0.262383814.53.085.89-0.094314.5-0.26383914.43.145.730.064614.4-0.413393914.43.145.730.064514.4-0.41394014.23.125.770.21114.2-0.437404014.23.125.770.21114.2-0.437404114.13.085.850.28214.1-0.274414114.13.085.850.28214.1-0.276414214.13.165.730.19414.1-0.295424214.13.165.730.19414.1-0.295424314.23.325.470.010614.2-0.385434314.23.325.470.010614.2-0.385434414.33.545.1-0.22914.3-0.452444414.33.545.1-0.22914.3-0.452130
444514.43.764.77-0.49814.4-0.498454514.43.764.77-0.49814.4-0.498454614.63.874.58-0.73814.6-0.738464614.63.874.58-0.73814.6-0.738464714.73.944.47-0.86714.7-0.867474714.73.944.47-0.86714.7-0.867474814.73.934.47-0.91514.7-0.915484814.73.934.47-0.91514.7-0.915484914.53.824.63-0.74514.5-0.745494914.53.824.63-0.74514.5-0.745495014.33.644.9-0.51114.3-0.561505014.33.644.9-0.51114.3-0.561505114.13.365.33-0.24514.1-0.689515114.13.365.33-0.24514.1-0.689515213.93.015.840.070813.9-0.729525213.93.015.840.070913.9-0.729525313.72.696.290.36913.7-0.668535313.72.696.290.36913.7-0.668535413.52.426.650.61413.5-0.592545413.52.426.650.61413.5-0.592545513.42.216.90.76413.4-0.434555513.42.216.90.76413.4-0.434555613.32.116.990.83413.3-0.346565613.32.116.990.83413.3-0.346565713.31.967.150.86913.3-0.406575713.31.967.150.86913.3-0.406575813.31.757.44113.3-0.575585813.31.757.44113.3-0.5745859131.586.90.95513-0.6995959131.586.90.95513-0.699130
596012.51.086.331.0112.5-0.952606012.51.086.331.0112.5-0.952606111.90.4346.191.2211.9-1.25616111.90.4346.191.2211.9-1.25616211.2-0.3716.431.5911.2-1.64626211.2-0.3716.431.5911.2-1.64626310.4-1.57.832.5510.4-2636310.4-1.57.832.5510.4-2.01636411.2-0.376.431.5911.2-1.63646411.2-0.376.431.5911.2-1.63646511.90.4366.191.2211.9-1.25656511.90.4366.191.2211.9-1.25656612.51.086.321.0112.5-0.947666612.51.086.321.0112.5-0.9476667131.586.890.96213-0.6946767131.586.890.96213-0.694676813.31.767.42113.3-0.57686813.31.767.42113.3-0.57686913.31.977.130.88313.3-0.403696913.31.977.130.88313.3-0.403697013.32.126.970.84713.3-0.342707013.32.126.970.84713.3-0.342707113.42.226.890.77813.4-0.43717113.42.226.890.77813.4-0.43717213.52.436.640.60213.5-0.588727213.52.436.640.60213.5-0.588727313.72.716.270.35413.7-0.664737313.72.716.270.35413.7-0.664737413.93.035.810.053413.9-0.726747413.93.035.810.053313.9-0.726130
747514.23.385.3-0.26314.2-0.686757514.23.385.3-0.26414.2-0.686757614.43.664.87-0.53314.4-0.559767614.43.664.87-0.53414.4-0.559767714.53.844.61-0.76814.5-0.768777714.53.844.61-0.76814.5-0.768777814.73.964.44-0.94114.7-0.941787814.73.964.44-0.94114.7-0.941787914.73.964.44-0.89714.7-0.897797914.73.964.44-0.89714.7-0.897798014.63.94.54-0.76914.6-0.769808014.63.94.54-0.76914.6-0.769808114.53.784.73-0.5314.5-0.53818114.53.784.73-0.5314.5-0.53818214.33.575.07-0.26514.3-0.461828214.33.575.07-0.26514.3-0.461828314.23.355.42-0.028414.2-0.389838314.23.355.42-0.028414.2-0.389838414.13.195.680.15114.1-0.298848414.13.195.680.15114.1-0.298848514.13.115.810.23614.1-0.282858514.13.115.810.23614.1-0.282858614.23.155.720.14214.2-0.445868614.23.155.720.14214.2-0.445868714.43.175.68-0.010214.4-0.421878714.43.175.68-0.010214.4-0.421878814.63.115.84-0.16314.6-0.269888814.63.115.84-0.16314.6-0.269888914.42.965.38-0.23714.4-0.346898914.42.965.38-0.23714.4-0.346130
899013.92.514.88-0.26213.9-0.568909013.92.514.88-0.26213.9-0.568909113.41.914.77-0.12413.4-0.858919113.41.914.77-0.12413.4-0.858919212.81.1750.20512.8-1.27929212.81.1750.20512.8-1.27929312.20.1756.270.98912.2-1.63939312.20.1756.270.98912.2-1.53939412.81.2250.18512.8-1.12949412.81.2250.18512.8-1.12949513.51.924.86-0.10613.5-0.708959513.51.924.86-0.10613.5-0.708959613.92.45.510.18813.9-0.323969613.92.45.510.18813.9-0.323969714.32.676.80.89714.3-0.209979714.32.676.80.89714.3-0.208979814.42.717.621.1314.4-0.313989814.42.717.621.1314.4-0.313989914.22.67.851.3414.2-0.355999914.22.67.851.3414.2-0.35599100142.468.151.5614-0.333100100142.468.151.5614-0.33310010113.82.348.431.7813.8-0.20510110113.82.348.431.7813.8-0.20510110213.72.348.481.813.7-0.14610210213.72.348.481.813.7-0.14610210313.72.448.341.713.7-0.21910310313.72.448.341.713.7-0.21910310413.82.618.081.5113.8-0.25910410413.82.618.081.5113.8-0.259130
10410513.92.817.751.313.9-0.23410510513.92.817.751.313.9-0.234105106142.967.511.1914-0.158106106142.967.511.1914-0.15810610713.93.057.361.213.9-0.10210710713.93.057.361.213.9-0.10210710813.83.097.31.3113.8-0.18510810813.83.097.31.3113.8-0.18510810913.63.067.341.5513.6-0.27510910913.63.067.341.5513.6-0.27610911013.42.987.461.8913.4-0.37911011013.42.987.461.8913.4-0.37911011113.12.827.672.3413.1-0.49411111113.12.827.672.3413.1-0.49411111212.72.617.962.8912.7-0.61611211212.72.617.962.8912.7-0.61611211312.22.348.343.5512.2-0.74411311312.22.348.343.5512.2-0.74411311411.72.028.794.3211.7-0.87511411411.72.028.794.3211.7-0.87511411511.11.669.315.1911.1-0.90711511511.11.669.315.1911.1-0.90711511610.41.289.645.8710.4-0.6211611610.41.289.645.8710.4-0.621161179.971.099.636.279.97-0.1551171179.971.099.636.279.97-0.1551171189.961.428.775.939.96-0.3771181189.961.428.775.939.96-0.37711811910.11.757.445.0610.1-0.6111911910.11.757.445.0610.1-0.61130
1191209.611.532.71.229.61-0.1841201209.611.532.71.229.61-0.1831201219.581.770.569-0.5229.58-0.6981211219.581.770.569-0.5229.58-0.6981211228.240.70.9450.1758.24-1.741221228.240.70.9450.1758.24-1.741221236.95-0.3661.470.8996.95-2.961231236.95-0.3661.470.8996.95-0.9761231246.96-0.341.440.8876.96-0.9611241246.96-0.341.440.8876.96-0.9611241257.2100.42407.21-0.9562、正常使用极限状态计算l裂缝宽度计算Wf≤0.1mml斜截面抗裂验算短期效应组合下最大主拉应力δtp≤0.5ftk=0.5×2.65=1.325(MPa)3、持久状况应力验算部分预应力混凝土B类构件在使用荷载作用下的正截面法向压应力及受拉钢筋应力应按开裂截面计算,斜截面按不开裂截面计算。l正截面抗裂:受压区混凝土边缘最大压应力δc≤0.5fck=0.5×32.4=16.2(MPa)l预应力钢筋拉应力δp≤0.65fpk=0.65×1860=1209(MPa)普通钢筋拉应力δs≤aesδcs(hs-x)/xl斜截面主应力验算:最大主压应力130
δcp≤0.6fck=0.6*32.4=19.44(MPa)最大主拉应力δtp≤0.5ftk=0.5*2.65=1.325(MPa)4、短暂状态应力验算l上缘混凝土应力:δc≥0l下缘混凝土应力:δtcc≤0.7fck=0.7*32.4=22.68(MPa)应力值见附表。附表1:项目最小值(MPa)限值(MPa)短期效应正应力上缘-0.9580下缘-1.17主拉应力-1.72-1.325附表2:项目最大值(MPa)限值(MPa)持久状况与短暂状况持久状况正应力上缘5.5316.2下缘8.94主压应力8.9419.44钢束最大应力12491209短暂状况正应力上缘12.822.68下缘9.53表中负值表示拉应力,正值为压应力。l附表1中在荷载短期效应下,主梁上缘、下缘出现了拉应力,采用普通钢筋补强,底板钢筋为HRB335钢筋,公称直径为20mm,公称截面面积314.2mm2,令1.72=nx314.2x280*10-6,得n=19.5,As=19.5x314.26127mm2;现底板下缘设81根φ20钢筋,As=81x314.2=25450mm2;顶板上缘设135根φ16钢筋,As=135x201.1=27149mm2,能够满足要求。l附表2中钢束最大应力1249MPa>容许应力1209Mpa,大于规范要求(相差3.3%),相差很小,可以看做满足规范要求。l附表2中最大主拉应力1.72MPa>1.325Mpa,按《桥规》D62中7.1.6条应按要求设计箍筋间距:按1m计算,箍筋间距150mm,箍筋采用φ20,Sv=fskAsv/δtpb=335x314.2*(1000/150)130
/(1.72x500x3)=272cm,设计按15cm间距布置箍筋(主梁横向钢筋)。5、支点处抗剪验算支点节点号最大剪力(KN)293003387206394809386901238930节点123处剪力最大,ΥoVd=1x9480=9480KN0.51x10-3bho=0.51x10-3*x(750*3)*(1800-35)=14321KNΥoVd=9480KN≤0.51x10-3bho=14321(KN)63节点处抗剪承载力满足规范要求。6、主梁计算主要结论结构极限承载力均满足规范要求,短期效应组合和长期效应组合正截面抗裂验算均满足全预应力混凝土受弯构件的要求。综上所述,各截面应力均满足规范限值。六、桥台处端横梁计算桥台处端横梁按普通钢筋混凝土连续梁形式进行计算,结构离散图如下:130
共分32个单位,剔除悬臂1-4、29-32单位进行计算。单跨恒载按三片腹板处的集中力加载,活载按均布荷载进行加载:l一跨梁重10005KN,按集中力分配到三片腹板:边腹板0.3*10005/2=1501KN中腹板0.4*10005/2=2001KNl桥面铺装按均布荷载加载:0.13*20*15*26/20*1.2=61KN/m(考虑人行道系数1.2)l活载按均布荷载加载:10.5*4+280*4/15+4*2.5*15*2/5=177KN/m。一、计算输出********************************************************************************施工阶段内力位移输出********************************************************************************第1施工阶段结构效应阶段支承反力汇总:阶段累计结果:节点号水平力竖向力弯矩60.000e+0002.401e+0030.000e+000177.227e-0132.370e+0030.000e+000280.000e+0002.401e+0030.000e+000阶段永久载结果:130
节点号水平力竖向力弯矩60.000e+0002.401e+0030.000e+000171.174e-0122.371e+0030.000e+000280.000e+0002.401e+0030.000e+000********************************************************************************正常使用阶段内力位移输出********************************************************************************正常使用阶段支承反力汇总:结构重力结果:节点号水平力竖向力弯矩60.000e+0002.401e+0030.000e+000177.227e-0132.370e+0030.000e+000280.000e+0002.401e+0030.000e+000荷载组合I支承反力组合结果:节点号=6内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力2.401e+0032.401e+0034.333e+0032.264e+0032.401e+0032.401e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=17内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力7.227e-0137.227e-0133.736e-012-1.474e-0127.227e-0137.227e-013竖向力2.370e+0032.370e+0032.882e+0031.809e+0032.370e+0032.370e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=28内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力2.401e+0032.401e+0034.333e+0032.264e+0032.401e+0032.401e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000130
荷载组合II支承反力组合结果:节点号=6内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力2.401e+0032.401e+0034.333e+0032.264e+0032.401e+0032.401e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=17内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力7.227e-0137.227e-0133.736e-012-1.474e-0127.227e-0137.227e-013竖向力2.370e+0032.370e+0032.882e+0031.809e+0032.370e+0032.370e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=28内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力2.401e+0032.401e+0034.333e+0032.264e+0032.401e+0032.401e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000荷载组合III支承反力组合结果:节点号=6内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向力2.401e+0032.401e+0034.402e+0032.230e+0032.401e+0032.401e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=17内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力7.227e-0137.227e-0133.759e-012-1.520e-0127.227e-0137.227e-013竖向力2.370e+0032.370e+0032.951e+0031.672e+0032.370e+0032.370e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000节点号=28内力性质水平最大水平最小竖向最大竖向最小弯矩最大弯矩最小水平力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000130
竖向力2.401e+0032.401e+0034.402e+0032.230e+0032.401e+0032.401e+003弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000********************************************************************************指定单元截面应力输出********************************************************************************第1施工阶段应力结果阶段累计应力:主截面:单元号左上缘左下缘右上缘右下缘501.0901.83601.8301.36701.3600.944800.94400.594900.59400.3051000.30500.07821100.07290.1090120.10900.1840130.18400.2250140.22500.2060150.20600.1270160.127000.01111700.01110.1270180.12700.2060190.20600.2250200.22500.1840210.18400.1090220.109000.07262300.077800.305130
2400.30500.5932500.59300.9432600.94301.362701.3601.832801.8301.09阶段永久载应力:主截面:单元号左上缘左下缘右上缘右下缘501.0901.83601.8301.36701.3600.944800.94400.595900.59500.3061000.30600.081100.07460.1070120.10700.1820130.18200.2220140.22200.2020150.20200.1230160.123000.01491700.01490.1230180.12300.2020190.20200.2220200.22200.1820210.18200.1070220.107000.07432300.079700.3062400.30600.5942500.59400.944130
2600.94401.362701.3601.832801.8301.09正常使用阶段应力计算结果主截面:结构重力应力结果单元号左上缘左下缘右上缘右下缘501.0901.83601.8301.36701.3600.944800.94400.594900.59400.3051000.30500.07821100.07290.1090120.10900.1840130.18400.2250140.22500.2060150.20600.1270160.127000.01111700.01110.1270180.12700.2060190.20600.2250200.22500.1840210.18400.1090220.109000.07262300.077800.3052400.30500.5932500.59300.9432600.94301.362701.3601.83130
2801.8301.09使用阶段荷载组合1应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉55003.761.093.76-0.43156003.761.093.76-0.43166005.21.835.2-0.71567005.21.835.2-0.71577004.091.094.09-0.64978004.091.094.09-0.64988003.130.4163.13-0.58389003.130.4163.13-0.583990.19502.3202.32-0.5179100.19502.3202.32-0.51710100.74101.6401.64-0.45110110.74101.6401.64-0.45111111.201.0401.2-0.37711121.201.0401.2-0.37712121.700.6401.7-0.29912131.700.6401.7-0.29913132.1800.66402.18-0.24813142.1800.66402.18-0.24814142.6400.74502.64-0.18414152.6400.74502.64-0.18415152.9700.88302.97-0.11915162.9700.88302.97-0.11916163.1601.0803.16-0.12316173.1601.0803.16-0.12317173.2101.3303.21-0.18917183.2101.3303.21-0.189130
18183.1601.0803.16-0.12318193.1601.0803.16-0.12319192.9700.88302.97-0.11919202.9700.88302.97-0.11920202.6400.74402.64-0.18320212.6400.74402.64-0.18321212.1800.66302.18-0.24821222.1800.66302.18-0.24822221.700.6401.7-0.29922231.700.6401.7-0.29923231.2301.1201.23-0.37823241.2301.1201.23-0.37824240.74101.6401.64-0.45124250.74101.6401.64-0.45125250.19602.3102.31-0.51725260.19602.3102.31-0.5172626003.130.4163.13-0.5832627003.130.4163.13-0.5832727004.091.094.09-0.6492728004.091.094.09-0.6492828005.21.835.2-1.142829005.21.835.2-1.14使用阶段荷载组合2应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉55003.761.093.76-0.43156003.761.093.76-0.43166005.21.835.2-0.71567005.21.835.2-0.71577004.091.094.09-0.649130
78004.091.094.09-0.64988003.130.4163.13-0.58389003.130.4163.13-0.583990.19502.3202.32-0.5179100.19502.3202.32-0.51710100.74101.6401.64-0.45110110.74101.6401.64-0.45111111.201.0401.2-0.37711121.201.0401.2-0.37712121.700.6401.7-0.29912131.700.6401.7-0.29913132.1800.66402.18-0.24813142.1800.66402.18-0.24814142.6400.74502.64-0.18414152.6400.74502.64-0.18415152.9700.88302.97-0.11915162.9700.88302.97-0.11916163.1601.0803.16-0.12316173.1601.0803.16-0.12317173.2101.3303.21-0.18917183.2101.3303.21-0.18918183.1601.0803.16-0.12318193.1601.0803.16-0.12319192.9700.88302.97-0.11919202.9700.88302.97-0.11920202.6400.74402.64-0.18320212.6400.74402.64-0.18321212.1800.66302.18-0.24821222.1800.66302.18-0.24822221.700.6401.7-0.299130
22231.700.6401.7-0.29923231.2301.1201.23-0.37823241.2301.1201.23-0.37824240.74101.6401.64-0.45124250.74101.6401.64-0.45125250.19602.3102.31-0.51725260.19602.3102.31-0.5172626003.130.4163.13-0.5832627003.130.4163.13-0.5832727004.091.094.09-0.6492728004.091.094.09-0.6492828005.21.835.2-1.142829005.21.835.2-1.14使用阶段荷载组合3应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉55003.761.093.76-0.43156003.761.093.76-0.43166005.21.835.2-0.74467005.21.835.2-0.74477004.131.034.13-0.67978004.131.034.13-0.67988003.20.2873.2-0.61389003.20.2873.2-0.613990.38602.4102.41-0.5479100.38602.4102.41-0.54710100.99501.7701.77-0.47110110.99501.7701.77-0.47111111.5101.1901.51-0.40511121.5101.1901.51-0.405130
12122.0900.82602.09-0.32812132.0900.82602.09-0.32813132.6100.87402.61-0.27713142.6100.87402.61-0.27714143.1400.98503.14-0.21214153.1400.98503.14-0.21215153.5301.1503.53-0.14815163.5301.1503.53-0.14816163.7801.3803.78-0.13716173.7801.3803.78-0.13717173.901.6603.9-0.20317183.901.6603.9-0.20318183.7801.3803.78-0.13718193.7801.3803.78-0.13719193.5301.1503.53-0.14819203.5301.1503.53-0.14820203.1400.98503.14-0.21220213.1400.98503.14-0.21221212.6100.87402.61-0.27721222.6100.87402.61-0.27722222.0900.82602.09-0.32822232.0900.82602.09-0.32823231.5401.2801.54-0.40623241.5401.2801.54-0.40624240.99501.7701.77-0.47124250.99501.7701.77-0.47125250.38702.4102.41-0.54725260.38702.4102.41-0.5472626003.20.2873.2-0.6132627003.20.2873.2-0.613130
2727004.131.034.13-0.6782728004.131.034.13-0.6782828005.21.835.2-1.142829005.21.835.2-1.14********************************************************************************指定单元截面裂缝宽度输出********************************************************************************单元号组合类型左上缘左下缘右上缘右下缘5组合I0.11400.15805组合II0.11400.15805组合III0.11400.15806组合I0.15800.12406组合II0.15800.12406组合III0.15800.12507组合I0.12400.094907组合II0.12400.094907组合III0.12500.096208组合I0.094900.07020.005818组合II0.094900.07020.005818组合III0.096200.07210.009599组合I0.07020.005810.04980.0229组合II0.07020.005810.04980.0229组合III0.07210.009590.05240.027110组合I0.04980.0220.03380.036410组合II0.04980.0220.03380.036410组合III0.05240.02710.03710.042711组合I0.02770.03640.0170.051611组合II0.02770.03640.0170.051611组合III0.03030.04270.02030.0594130
12组合I0.0170.05160.01760.066112组合II0.0170.05160.01760.066112组合III0.02030.05940.02130.074913组合I0.01760.06610.01980.080313组合II0.01760.06610.01980.080313组合III0.02130.07490.0240.090414组合I0.01980.08030.02350.090314组合II0.01980.08030.02350.090314组合III0.0240.09040.02820.10215组合I0.02350.09030.02870.096115组合II0.02350.09030.02870.096115组合III0.02820.1020.0340.10916组合I0.02870.09610.03540.097516组合II0.02870.09610.03540.097516组合III0.0340.1090.04130.11117组合I0.03540.09750.02870.096117组合II0.03540.09750.02870.096117组合III0.04130.1110.0340.10918组合I0.02870.09610.02350.090318组合II0.02870.09610.02350.090318组合III0.0340.1090.02820.10219组合I0.02350.09030.01980.080319组合II0.02350.09030.01980.080319组合III0.02820.1020.0240.090420组合I0.01980.08030.01760.066120组合II0.01980.08030.01760.066120组合III0.0240.09040.02130.074921组合I0.01760.06610.0170.051621组合II0.01760.06610.0170.051621组合III0.02130.07490.02030.0595130
22组合I0.0170.05160.02760.036422组合II0.0170.05160.02760.036422组合III0.02030.05950.03030.042723组合I0.03380.03640.04980.02223组合II0.03380.03640.04980.02223组合III0.03710.04270.05240.027124组合I0.04980.0220.07010.0058224组合II0.04980.0220.07010.0058224组合III0.05240.02710.07210.0096125组合I0.07010.005820.0949025组合II0.07010.005820.0949025组合III0.07210.009610.0962026组合I0.094900.124026组合II0.094900.124026组合III0.096200.125027组合I0.12400.158027组合II0.12400.158027组合III0.12500.158028组合I0.15800.114028组合II0.15800.114028组合III0.15800.1140一、桥台处端横梁计算主要结论结构极限承载力均满足规范要求,短期效应组合和长期效应组合正截面抗裂验算均满足普通钢筋混凝土受弯构件的要求。最大裂缝宽度为0.158mm<0.2mm,满足规范要求。综上所述,各截面应力均满足规范限值。七、桥墩伸缩缝处横梁计算横梁按简支梁形式进行计算,结构离散图如下:130
共分32个单位,剔除悬臂1-4、29-32单位进行计算。横梁按全预应力混凝土构件进行计算。单跨恒载按三片腹板处的集中力加载,活载按均布荷载进行加载:l一跨梁重10005KN,按集中力分配到三片腹板:边腹板0.3*10005/2=1501KN中腹板0.4*10005/2=2001KNl桥面铺装按均布荷载加载:0.13*20*15*26/20*1.2=61KN/m(考虑人行道系数1.2)l活载按均布荷载加载:10.5*4+280*4/15+4*2.5*15*2/5=177KN/m。1、指定单元截面应力输出正常使用阶段应力计算结果使用阶段荷载组合1应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉55564.74.475.014.795.01-0.17664.74.475.014.795.01-0.17675.75.284.13.865.7-0.157775.75.284.13.865.7-0.157786.675.973.32.986.67-0.144886.675.973.32.986.67-0.144897.586.532.672.087.58-0.131130
997.586.532.672.087.58-0.1319108.456.942.21.28.45-0.11910108.456.942.21.28.45-0.11910119.517.431.950.4589.51-0.031611119.517.431.950.4589.51-0.031611129.066.383.291.239.06-0.43712129.066.383.291.239.06-0.20312139.687.222.530.79.68-0.055313139.687.222.530.79.68-0.055313149.197.112.71.199.19-0.27414149.197.112.71.199.19-0.27414157.726.023.92.717.72-0.35615157.726.023.92.717.72-0.35615166.875.384.993.996.87-0.059416166.875.384.993.996.87-0.059416177.255.814.913.967.25-0.05717177.255.814.913.967.25-0.056717186.875.384.993.996.87-0.060118186.875.384.993.996.87-0.060118197.726.023.92.77.72-0.35619197.726.023.92.77.72-0.35619209.197.112.691.199.19-0.27420209.197.112.691.199.19-0.27420219.687.222.530.6999.68-0.055621219.687.222.530.6999.68-0.055621229.066.383.291.239.06-0.20322229.066.383.291.239.06-0.43722239.517.431.960.4619.51-0.031123239.517.431.960.4619.51-0.031123248.456.932.211.28.45-0.119130
24248.456.932.211.28.45-0.11924257.586.532.682.087.58-0.13125257.586.532.682.087.58-0.13125266.665.973.32.986.66-0.14426266.665.973.32.986.66-0.14426275.75.274.13.865.7-0.15727275.75.274.13.865.7-0.15727284.694.465.014.795.01-0.1728284.694.465.014.795.01-0.172829使用阶段荷载组合2应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉555610.10.7455.673.5310.1-0.176610.10.7455.673.5310.1-0.176711.11.164.762.9911.1-0.1577711.11.164.762.9911.1-0.1577812.11.453.962.5112.1-0.1448812.11.453.962.5112.1-0.14489131.63.332.0113-0.13199131.63.332.0113-0.13191013.91.612.861.5313.9-0.119101013.91.612.861.5313.9-0.1191011151.642.611.1715-0.03451111151.642.611.1715-0.0345111214.50.3863.952.0814.5-0.47121214.50.3863.952.0814.5-0.22121315.11.233.191.5315.1-0.0601131315.11.233.191.5315.1-0.0601130
131414.61.383.351.7714.6-0.274141414.61.383.351.7714.6-0.274141513.20.7414.562.8313.2-0.356151513.20.7414.562.8313.2-0.356151612.30.4155.653.7212.3-0.0594161612.30.4155.653.7212.3-0.0594161712.70.9055.573.5612.7-0.0614171712.70.9055.573.5612.7-0.0611171812.30.4165.653.7212.3-0.0601181812.30.4165.653.7212.3-0.0601181913.20.7444.562.8313.2-0.356191913.20.7444.562.8313.2-0.356192014.61.393.351.7714.6-0.274202014.61.393.351.7714.6-0.274202115.11.233.181.5315.1-0.0604212115.11.233.181.5315.1-0.0604212214.50.3863.952.0814.5-0.22222214.50.3863.952.0814.5-0.472223151.642.611.1815-0.0342323151.642.611.1815-0.034232413.91.62.871.5413.9-0.119242413.91.62.871.5413.9-0.1192425131.63.332.0113-0.1312525131.63.332.0113-0.131252612.11.453.962.5112.1-0.144262612.11.453.962.5112.1-0.144262711.11.154.762.9911.1-0.157272711.11.154.762.9911.1-0.157272810.10.7425.673.5310.1-0.17282810.10.7425.673.5310.1-0.17130
2829使用阶段荷载组合3应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉555611.51.065.834.3811.5-0.176611.51.065.834.3811.5-0.176712.51.874.923.4512.5-0.1577712.51.874.923.4512.5-0.1577813.52.574.122.5613.5-0.1448813.52.574.122.5613.5-0.1448914.43.123.51.6714.4-0.1319914.43.123.51.6714.4-0.13191015.33.533.030.78915.3-0.119101015.33.533.030.78915.3-0.119101116.34.032.780.04616.3-0.0353111116.34.032.780.04616.3-0.0353111215.92.984.110.81715.9-0.479121215.92.984.110.81715.9-0.225121316.53.813.350.28816.5-0.0614131316.53.813.350.28816.5-0.06141314163.73.520.78316-0.2741414163.73.520.78316-0.274141514.52.614.732.314.5-0.356151514.52.614.732.314.5-0.356151613.71.975.813.5813.7-0.0594161613.71.975.813.5813.7-0.0594161714.12.415.733.5514.1-0.0627171714.12.415.733.5514.1-0.0623171813.71.975.813.5813.7-0.0601130
181813.71.975.813.5813.7-0.0601181914.52.624.722.2914.5-0.356191914.52.624.722.2914.5-0.3561920163.713.520.77916-0.2742020163.713.520.77916-0.274202116.53.823.350.28716.5-0.0618212116.53.823.350.28716.5-0.0618212215.92.984.110.81715.9-0.225222215.92.984.110.81715.9-0.479222316.34.022.780.04916.3-0.0348232316.34.022.780.04916.3-0.0348232415.33.533.030.79315.3-0.119242415.33.533.030.79315.3-0.119242514.43.123.51.6714.4-0.131252514.43.123.51.6714.4-0.131252613.52.574.122.5713.5-0.144262613.52.574.122.5713.5-0.144262712.51.874.933.4512.5-0.157272712.51.874.933.4512.5-0.157272811.51.065.844.3811.5-0.17282811.51.065.844.3811.5-0.1728292、持久状况承载能力极限状态计算l正截面强度验算见主梁承载能力组合Ⅰ计算结果:均满足强度要求。l斜截面强度验算参照以往设计,斜截面抗剪计算满足设计要求。3、持久状况正常使用极限状态计算130
抗裂验算:l正截面抗裂:短期效应组合下δst-0.85δpc≤0(MPa)l斜截面抗裂:短期效应组合下δtp≤0.4ftk=0.4×2.65=1.06(MPa)应力值见附表,且均满足规范要求。4、持久状况和短暂状况构件的应力验算应力验算:1.持久状况使用阶段:l正截面受压区混凝土最大压应力δc≤0.5fck=0.5×32.4=16.2(MPa)受拉区预应力钢筋最大拉应力δp(MPa)≤0.65fpk=0.65×1860=1209(MPa)l斜截面混凝土主压应力δcp≤0.6fck=0.6×32.4=19.44(MPa)2.短暂状况施工阶段:l正截面受压区混凝土边缘压应力δcc≤0.7fck=0.7×32.4=22.68(MPa)施工阶段、使用阶段应力值见附表,均满足规范要求。附表1:项目最小值限值短期效应正应力上缘0.3860下缘1.18主拉应力-0.17-1.06130
附表2:项目最大值限值持久状况与短暂状况持久状况正应力上缘9.6816.2下缘5.01主压应力9.6819.44钢束最大应力11381209短暂状况正应力上缘15.122.68下缘5.67表中负值表示拉应力,正值为压应力。5、伸缩缝桥墩处端横梁计算主要结论结构极限承载力均满足规范要求,短期效应组合和长期效应组合正截面抗裂验算均满足全预应力混凝土受弯构件的要求。综上所述,各截面应力均满足规范限值。八、中横梁计算横梁按简支梁形式进行计算,结构离散图如下:共分32个单位,剔除悬臂1-4、29-32单位进行计算。横梁按全预应力混凝土构件进行计算。单跨恒载按三片腹板处的集中力加载,活载按均布荷载进行加载:130
l一跨梁重9916KN,按集中力分配到三片腹板:外腹板为0.3*9916=2980KN;中腹板为0.4*9916=3970KN。l桥面铺装按均布荷载加载:0.13*20*30*26/20*1.2=122KN/m(考虑人行道系数1.2)。l活载按均布荷载加载:10.5*4+280*4/15+4*2.5*30*2/5=237KN/m。1、指定单元截面应力输出正常使用阶段应力计算结果使用阶段荷载组合1应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉5500009.69e-017-6.79e-016560.750.69810.29.7310.2-0.302660.750.69810.29.7310.2-0.302672.211.988.798.48.79-0.287772.211.988.798.48.79-0.287783.633.197.497.117.49-0.272883.633.197.497.117.49-0.2728954.296.275.846.27-0.2579954.296.275.846.27-0.2579106.325.275.174.596.32-0.23910106.325.275.174.596.32-0.23910117.786.314.663.737.78-0.02211117.786.314.663.737.78-0.02211127.055.186.14.87.05-0.39912127.055.186.14.87.05-0.18412137.826.085.214.057.82-0.16313137.826.085.214.057.82-0.16313148.426.864.513.538.42-0.0038714148.426.864.513.538.42-0.0038714157.686.334.874.077.68-0.156130
15157.686.334.874.077.68-0.15615167.316.15.554.887.31-0.0082716167.316.15.554.887.31-0.0082716177.66.435.284.647.6-0.073817177.66.435.284.647.6-0.073817187.316.15.554.887.31-0.0084118187.316.15.554.887.31-0.0084118197.686.334.874.067.68-0.15519197.686.334.874.067.68-0.15519208.436.864.513.538.43-0.0039620208.436.864.513.538.43-0.0039620217.826.085.214.057.82-0.16321217.826.085.214.057.82-0.16321227.055.186.14.87.05-0.18422227.055.186.14.87.05-0.39922237.786.314.663.737.78-0.021923237.786.314.663.737.78-0.021923246.315.275.184.66.31-0.23924246.315.275.184.66.31-0.23924254.994.286.285.856.28-0.25725254.994.286.285.856.28-0.25725263.633.187.497.117.49-0.27226263.633.187.497.117.49-0.27226272.211.988.88.48.8-0.28727272.211.988.88.48.8-0.28727280.7450.69310.29.7310.2-0.30228280.7450.69310.29.7310.2-0.302282900003.77e-014-3.81e-014使用阶段荷载组合2应力:主截面:130
单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉555.451.93e-0140.659-1.93e-0145.45-0.925566.20.47710.97.7610.9-0.33666.20.47710.97.7610.9-0.33677.661.239.456.969.45-0.287777.661.239.456.969.45-0.287789.081.918.156.199.08-0.272889.081.918.156.199.08-0.2728910.42.496.935.4610.4-0.2579910.42.496.935.4610.4-0.25791011.82.945.834.7311.8-0.239101011.82.945.834.7311.8-0.239101113.23.45.324.3213.2-0.0237111113.23.45.324.3213.2-0.0237111212.52.076.765.5112.5-0.426121212.52.076.765.5112.5-0.197121313.32.975.874.7613.3-0.174131313.32.975.874.7613.3-0.174131413.93.85.174.1613.9-0.00416141413.93.85.174.1613.9-0.00416141513.13.615.534.4213.1-0.156151513.13.615.534.4213.1-0.156151612.83.616.214.9112.8-0.00827161612.83.616.214.9112.8-0.008271617134.045.944.5713-0.0791717134.045.944.5713-0.079171812.83.626.214.9112.8-0.00841181812.83.626.214.9112.8-0.00841181913.13.615.534.4213.1-0.155191913.13.615.534.4213.1-0.155130
192013.93.815.174.1613.9-0.00426202013.93.815.174.1613.9-0.00426202113.32.975.874.7613.3-0.174212113.32.975.874.7613.3-0.174212212.52.076.765.5112.5-0.197222212.52.076.765.5112.5-0.426222313.23.45.324.3213.2-0.0236232313.23.45.324.3213.2-0.0236232411.82.935.844.7411.8-0.239242411.82.935.844.7411.8-0.239242510.42.486.935.4610.4-0.257252510.42.486.935.4610.4-0.25725269.071.918.156.29.07-0.27226269.071.918.156.29.07-0.27226277.651.239.466.969.46-0.28727277.651.239.466.969.46-0.28727286.190.47310.97.7710.9-0.33128286.190.47310.97.7710.9-0.33128295.454.66e-0140.659-4.66e-0145.45-0.925使用阶段荷载组合3应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉556.8100.82406.81-1.16567.560.698119.7311-0.361667.560.698119.7311-0.361679.021.989.628.49.62-0.287779.021.989.628.49.62-0.2877810.43.198.317.1110.4-0.2728810.43.198.317.1110.4-0.2728911.84.297.095.8411.8-0.257130
9911.84.297.095.8411.8-0.25791013.15.2764.5913.1-0.239101013.15.2764.5913.1-0.239101114.66.315.483.7314.6-0.0242111114.66.315.483.7314.6-0.0242111213.95.186.934.813.9-0.433121213.95.186.934.813.9-0.2121314.66.086.034.0514.6-0.178131314.66.086.034.0514.6-0.178131415.26.865.343.5315.2-0.00424141415.26.865.343.5315.2-0.00424141514.56.335.74.0714.5-0.156151514.56.335.74.0714.5-0.156151614.16.16.384.8814.1-0.00827161614.16.16.384.8814.1-0.00827161714.46.436.14.6414.4-0.0804171714.46.436.14.6414.4-0.0804171814.16.16.384.8814.1-0.00841181814.16.16.384.8814.1-0.00841181914.56.335.694.0614.5-0.155191914.56.335.694.0614.5-0.155192015.26.865.333.5315.2-0.00434202015.26.865.333.5315.2-0.00434202114.66.086.034.0514.6-0.178212114.66.086.034.0514.6-0.178212213.95.186.934.813.9-0.2222213.95.186.934.813.9-0.433222314.66.315.493.7314.6-0.024232314.66.315.493.7314.6-0.024232413.15.2764.613.1-0.239130
242413.15.2764.613.1-0.239242511.84.287.15.8511.8-0.257252511.84.287.15.8511.8-0.257252610.43.188.327.1110.4-0.272262610.43.188.327.1110.4-0.27226279.021.989.628.49.62-0.28727279.021.989.628.49.62-0.28727287.550.693119.7311-0.36128287.550.693119.7311-0.36128296.8100.82406.81-1.162、持久状况承载能力极限状态计算l正截面强度验算见主梁承载能力组合Ⅰ计算结果:均满足强度要求。l斜截面强度验算参照以往设计,斜截面抗剪计算满足设计要求。3、持久状况正常使用极限状态计算抗裂验算:l正截面抗裂:短期效应组合下δst-0.85δpc≤0(MPa)l斜截面抗裂:短期效应组合下δtp≤0.4ftk=0.4×2.65=1.06(MPa)应力值见附表,且均满足规范要求。4、持久状况和短暂状况构件的应力验算应力验算:1.持久状况使用阶段:l正截面130
受压区混凝土最大压应力δc≤0.5fck=0.5×32.4=16.2(MPa)受拉区预应力钢筋最大拉应力δp(MPa)≤0.65fpk=0.65×1860=1209(MPa)l斜截面混凝土主压应力δcp≤0.6fck=0.6×32.4=19.44(MPa)2.短暂状况施工阶段:l正截面受压区混凝土边缘压应力δcc≤0.7fck=0.7×32.4=22.68(MPa)施工阶段、使用阶段应力值见附表,均满足规范要求。附表1:项目最小值限值短期效应正应力上缘0.4730下缘4.16主拉应力-0.000416-1.06附表2:项目最大值限值持久状况与短暂状况持久状况正应力上缘8.4316.2下缘10.2主压应力10.219.44钢束最大应力11411209短暂状况正应力上缘13.922.68下缘10.9表中负值表示拉应力,正值为压应力。5、中横梁计算主要结论结构极限承载力均满足规范要求,短期效应组合和长期效应组合正截面抗裂验算均满足全预应力混凝土受弯构件的要求。综上所述,各截面应力均满足规范限值。130
九、悬臂计算本桥悬臂长度为4000mm,取1000mm板宽为计算单位。人行道宽2500mm,根据桥规,车轮沿人行道边缘500mm,可布置一个车轮,按140/2=70KN计算,在主梁位置,活载由人群荷载和车辆荷载组成,不考虑相邻板的应力分布有利情况。l桥面铺装按均布荷载加载:0.13*4.5*26=15.21KN/ml人行道板及人行道地梁按均布荷载加载:0.624*26/2.5=6.5KN/ml栏杆柱及灯柱按集中力加载在1号单元,加载作用点距单元左截面100mm,集中力1.86KN+7.4KN=9.26KNl悬臂结构重按集中力加载:(0.2+0.5)x4/2x1x26=36.4KN悬臂重心距腹板L=1600mml9号单元结构重按集中力加载:0.5x1.8x26=23.4KN9号单元重心为9号单元中心。1、内力计算********************************************************************************施工阶段内力位移输出********************************************************************************第1施工阶段结构效应阶段累计结果:单元号节点号轴力剪力弯矩11-1.784e-013-2.557e-0129.446e-013128.954e-0012.420e+001-7.414e+000229.196e-001-2.420e+001-7.414e+000231.514e+0003.985e+001-2.341e+001331.474e+000-3.985e+001-2.341e+001342.080e+0005.620e+001-4.741e+001442.136e+000-5.620e+001-4.741e+001452.784e+0007.326e+001-7.977e+001552.711e+000-7.326e+001-7.977e+001564.714e+0001.274e+002-1.245e+002664.841e+000-1.274e+002-1.245e+002675.419e+0001.426e+002-1.920e+002777.865e+000-2.126e+002-1.920e+002788.454e+0002.285e+002-3.023e+002888.682e+000-2.285e+002-3.023e+002899.313e+0002.451e+002-4.207e+002993.193e-0138.739e+002-4.207e+002130
9103.193e-013-8.091e+002-1.155e-014节点号水平位移竖向位移转角位移1-1.530e-004-5.643e-0032.194e-0032-1.202e-004-4.554e-0032.147e-0033-8.778e-005-3.510e-0032.013e-0034-5.945e-005-2.552e-0031.806e-0035-3.459e-005-1.712e-0031.546e-0036-1.573e-005-1.012e-0031.249e-0037-2.448e-006-4.726e-0048.993e-00482.894e-006-1.236e-0044.820e-00499.483e-0070.000e+0003.751e-006阶段永久载结果:单元号节点号轴力剪力弯矩11-3.613e-013-3.684e-0129.575e-013128.954e-0012.420e+001-7.414e+000229.196e-001-2.420e+001-7.414e+000231.514e+0003.985e+001-2.341e+001331.474e+000-3.985e+001-2.341e+001342.080e+0005.620e+001-4.741e+001442.136e+000-5.620e+001-4.741e+001452.784e+0007.326e+001-7.977e+001552.711e+000-7.326e+001-7.977e+001564.714e+0001.274e+002-1.245e+002664.841e+000-1.274e+002-1.245e+002675.419e+0001.426e+002-1.920e+002777.865e+000-2.126e+002-1.920e+002788.454e+0002.285e+002-3.023e+002888.682e+000-2.285e+002-3.023e+002899.313e+0002.451e+002-4.207e+002999.441e-0138.739e+002-4.207e+0029109.441e-013-8.091e+002-2.665e-014节点号水平位移竖向位移转角位移1-1.414e-004-3.749e-0031.435e-0032-1.150e-004-3.034e-0031.414e-0033-8.886e-005-2.345e-0031.333e-0034-6.540e-005-1.710e-0031.202e-0035-4.418e-005-1.150e-0031.033e-0036-2.692e-005-6.810e-0048.377e-0047-1.326e-005-3.187e-0046.056e-0048-4.712e-006-8.343e-0053.259e-0049-8.526e-0070.000e+0002.623e-006********************************************************************************正常使用阶段内力位移输出********************************************************************************130
结构重力结果:单元号节点号轴力剪力弯矩11-1.784e-013-2.557e-0129.446e-013128.954e-0012.420e+001-7.414e+000229.196e-001-2.420e+001-7.414e+000231.514e+0003.985e+001-2.341e+001331.474e+000-3.985e+001-2.341e+001342.080e+0005.620e+001-4.741e+001442.136e+000-5.620e+001-4.741e+001452.784e+0007.326e+001-7.977e+001552.711e+000-7.326e+001-7.977e+001564.714e+0001.274e+002-1.245e+002664.841e+000-1.274e+002-1.245e+002675.419e+0001.426e+002-1.920e+002777.865e+000-2.126e+002-1.920e+002788.454e+0002.285e+002-3.023e+002888.682e+000-2.285e+002-3.023e+002899.313e+0002.451e+002-4.207e+002993.193e-0138.739e+002-4.207e+0029103.193e-013-8.091e+002-1.155e-014节点号水平位移竖向位移转角位移1-1.530e-004-5.643e-0032.194e-0032-1.202e-004-4.554e-0032.147e-0033-8.778e-005-3.510e-0032.013e-0034-5.945e-005-2.552e-0031.806e-0035-3.459e-005-1.712e-0031.546e-0036-1.573e-005-1.012e-0031.249e-0037-2.448e-006-4.726e-0048.993e-00482.894e-006-1.236e-0044.820e-00499.483e-0070.000e+0003.751e-006承载能力极限状态荷载组合I内力结果:单元号=1,左节点号=1内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=1,右节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.075e+0008.954e-0011.075e+0008.954e-0018.954e-0011.075e+000剪力2.904e+0012.420e+0012.904e+0012.420e+0012.420e+0012.904e+001弯矩-8.897e+000-7.414e+000-8.897e+000-7.414e+000-7.414e+000-8.897e+000单元号=2,左节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.104e+0009.196e-0019.196e-0011.104e+0009.196e-0011.104e+000剪力-2.904e+001-2.420e+001-2.420e+001-2.904e+001-2.420e+001-2.904e+001130
弯矩-8.897e+000-7.414e+000-7.414e+000-8.897e+000-7.414e+000-8.897e+000单元号=2,右节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.817e+0001.514e+0001.817e+0001.514e+0001.514e+0001.817e+000剪力4.782e+0013.985e+0014.782e+0013.985e+0013.985e+0014.782e+001弯矩-2.809e+001-2.341e+001-2.809e+001-2.341e+001-2.341e+001-2.809e+001单元号=3,左节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.769e+0001.474e+0001.474e+0001.769e+0001.474e+0001.769e+000剪力-4.782e+001-3.985e+001-3.985e+001-4.782e+001-3.985e+001-4.782e+001弯矩-2.809e+001-2.341e+001-2.341e+001-2.809e+001-2.341e+001-2.809e+001单元号=3,右节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.495e+0002.080e+0002.495e+0002.080e+0002.080e+0002.495e+000剪力6.745e+0015.620e+0016.745e+0015.620e+0015.620e+0016.745e+001弯矩-5.689e+001-4.741e+001-5.689e+001-4.741e+001-4.741e+001-5.689e+001单元号=4,左节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.563e+0002.136e+0002.136e+0002.563e+0002.136e+0002.563e+000剪力-6.744e+001-5.620e+001-5.620e+001-6.744e+001-5.620e+001-6.744e+001弯矩-5.689e+001-4.741e+001-4.741e+001-5.689e+001-4.741e+001-5.689e+001单元号=4,右节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.341e+0002.784e+0003.341e+0002.784e+0002.784e+0003.341e+000剪力8.791e+0017.326e+0018.791e+0017.326e+0017.326e+0018.791e+001弯矩-9.572e+001-7.977e+001-9.572e+001-7.977e+001-7.977e+001-9.572e+001单元号=5,左节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.253e+0002.711e+0002.711e+0003.253e+0002.711e+0003.253e+000剪力-8.791e+001-7.326e+001-7.326e+001-8.791e+001-7.326e+001-8.791e+001弯矩-9.572e+001-7.977e+001-7.977e+001-9.572e+001-7.977e+001-9.572e+001单元号=5,右节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力5.656e+0004.714e+0005.656e+0004.714e+0004.714e+0005.656e+000剪力1.529e+0021.274e+0021.529e+0021.274e+0021.274e+0021.529e+002弯矩-1.494e+002-1.245e+002-1.494e+002-1.245e+002-1.245e+002-1.494e+002单元号=6,左节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力5.809e+0004.841e+0004.841e+0005.809e+0004.841e+0005.809e+000剪力-1.529e+002-1.274e+002-1.274e+002-1.529e+002-1.274e+002-1.529e+002弯矩-1.494e+002-1.245e+002-1.245e+002-1.494e+002-1.245e+002-1.494e+002单元号=6,右节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力6.503e+0005.419e+0006.503e+0005.419e+0005.419e+0006.503e+000剪力1.711e+0021.426e+0021.711e+0021.426e+0021.426e+0021.711e+002130
弯矩-2.304e+002-1.920e+002-2.304e+002-1.920e+002-1.920e+002-2.304e+002单元号=7,左节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力9.438e+0007.865e+0007.865e+0009.438e+0007.865e+0009.438e+000剪力-2.551e+002-2.126e+002-2.126e+002-2.551e+002-2.126e+002-2.551e+002弯矩-2.304e+002-1.920e+002-1.920e+002-2.304e+002-1.920e+002-2.304e+002单元号=7,右节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.014e+0018.454e+0001.014e+0018.454e+0008.454e+0001.014e+001剪力2.742e+0022.285e+0022.742e+0022.285e+0022.285e+0022.742e+002弯矩-3.628e+002-3.023e+002-3.628e+002-3.023e+002-3.023e+002-3.628e+002单元号=8,左节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.042e+0018.682e+0008.682e+0001.042e+0018.682e+0001.042e+001剪力-2.742e+002-2.285e+002-2.285e+002-2.742e+002-2.285e+002-2.742e+002弯矩-3.628e+002-3.023e+002-3.023e+002-3.628e+002-3.023e+002-3.628e+002单元号=8,右节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.118e+0019.313e+0001.118e+0019.313e+0009.313e+0001.118e+001剪力2.941e+0022.451e+0022.941e+0022.451e+0022.451e+0022.941e+002弯矩-5.049e+002-4.207e+002-5.049e+002-4.207e+002-4.207e+002-5.049e+002单元号=9,左节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.832e-0133.193e-0133.832e-0133.193e-0133.193e-0133.832e-013剪力1.049e+0038.739e+0021.049e+0038.739e+0028.739e+0021.049e+003弯矩-5.049e+002-4.207e+002-5.049e+002-4.207e+002-4.207e+002-5.049e+002单元号=9,右节点号=10内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.832e-0133.193e-0133.193e-0133.832e-0133.193e-0133.832e-013剪力-9.709e+002-8.091e+002-8.091e+002-9.709e+002-8.091e+002-9.709e+002弯矩-1.386e-014-1.155e-014-1.155e-014-1.386e-014-1.155e-014-1.386e-014正常使用极限状态荷载组合I内力结果:单元号=1,左节点号=1内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=1,右节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.954e-0018.954e-0018.954e-0018.954e-0018.954e-0018.954e-001剪力2.420e+0012.420e+0012.420e+0012.420e+0012.420e+0012.420e+001弯矩-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000单元号=2,左节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力9.196e-0019.196e-0019.196e-0019.196e-0019.196e-0019.196e-001130
剪力-2.420e+001-2.420e+001-2.420e+001-2.420e+001-2.420e+001-2.420e+001弯矩-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000单元号=2,右节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.514e+0001.514e+0001.514e+0001.514e+0001.514e+0001.514e+000剪力3.985e+0013.985e+0013.985e+0013.985e+0013.985e+0013.985e+001弯矩-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001单元号=3,左节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.474e+0001.474e+0001.474e+0001.474e+0001.474e+0001.474e+000剪力-3.985e+001-3.985e+001-3.985e+001-3.985e+001-3.985e+001-3.985e+001弯矩-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001单元号=3,右节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.080e+0002.080e+0002.080e+0002.080e+0002.080e+0002.080e+000剪力5.620e+0015.620e+0015.620e+0015.620e+0015.620e+0015.620e+001弯矩-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001单元号=4,左节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.136e+0002.136e+0002.136e+0002.136e+0002.136e+0002.136e+000剪力-5.620e+001-5.620e+001-5.620e+001-5.620e+001-5.620e+001-5.620e+001弯矩-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001单元号=4,右节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.784e+0002.784e+0002.784e+0002.784e+0002.784e+0002.784e+000剪力7.326e+0017.326e+0017.326e+0017.326e+0017.326e+0017.326e+001弯矩-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001单元号=5,左节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.711e+0002.711e+0002.711e+0002.711e+0002.711e+0002.711e+000剪力-7.326e+001-7.326e+001-7.326e+001-7.326e+001-7.326e+001-7.326e+001弯矩-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001单元号=5,右节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力4.714e+0004.714e+0004.714e+0004.714e+0004.714e+0004.714e+000剪力1.274e+0021.274e+0021.274e+0021.274e+0021.274e+0021.274e+002弯矩-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002单元号=6,左节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力4.841e+0004.841e+0004.841e+0004.841e+0004.841e+0004.841e+000剪力-1.274e+002-1.274e+002-1.274e+002-1.274e+002-1.274e+002-1.274e+002弯矩-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002单元号=6,右节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力5.419e+0005.419e+0005.419e+0005.419e+0005.419e+0005.419e+000130
剪力1.426e+0021.426e+0021.426e+0021.426e+0021.426e+0021.426e+002弯矩-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002单元号=7,左节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力7.865e+0007.865e+0007.865e+0007.865e+0007.865e+0007.865e+000剪力-2.126e+002-2.126e+002-2.126e+002-2.126e+002-2.126e+002-2.126e+002弯矩-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002单元号=7,右节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.454e+0008.454e+0008.454e+0008.454e+0008.454e+0008.454e+000剪力2.285e+0022.285e+0022.285e+0022.285e+0022.285e+0022.285e+002弯矩-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002单元号=8,左节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.682e+0008.682e+0008.682e+0008.682e+0008.682e+0008.682e+000剪力-2.285e+002-2.285e+002-2.285e+002-2.285e+002-2.285e+002-2.285e+002弯矩-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002单元号=8,右节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力9.313e+0009.313e+0009.313e+0009.313e+0009.313e+0009.313e+000剪力2.451e+0022.451e+0022.451e+0022.451e+0022.451e+0022.451e+002弯矩-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002单元号=9,左节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.193e-0133.193e-0133.193e-0133.193e-0133.193e-0133.193e-013剪力8.739e+0028.739e+0028.739e+0028.739e+0028.739e+0028.739e+002弯矩-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002单元号=9,右节点号=10内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.193e-0133.193e-0133.193e-0133.193e-0133.193e-0133.193e-013剪力-8.091e+002-8.091e+002-8.091e+002-8.091e+002-8.091e+002-8.091e+002弯矩-1.155e-014-1.155e-014-1.155e-014-1.155e-014-1.155e-014-1.155e-014正常使用极限状态荷载组合I位移结果:节点号=1位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移3.657e-004-1.530e-004-1.530e-0043.657e-0043.657e-004-1.530e-004竖向位移-9.418e-003-5.643e-003-5.643e-003-9.418e-003-9.418e-003-5.643e-003转角位移3.893e-0032.194e-0032.194e-0033.893e-0033.893e-0032.194e-003节点号=2位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移3.539e-004-1.202e-004-1.202e-0043.539e-0043.539e-004-1.202e-004竖向位移-7.510e-003-4.554e-003-4.554e-003-7.510e-003-7.510e-003-4.554e-003转角位移3.704e-0032.147e-0032.147e-0033.704e-0033.704e-0032.147e-003节点号=3位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角130
水平位移3.375e-004-8.778e-005-8.778e-0053.375e-0043.375e-004-8.778e-005竖向位移-5.729e-003-3.510e-003-3.510e-003-5.729e-003-5.729e-003-3.510e-003转角位移3.391e-0032.013e-0032.013e-0033.391e-0033.391e-0032.013e-003节点号=4位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移3.119e-004-5.945e-005-5.945e-0053.119e-0043.119e-004-5.945e-005竖向位移-4.128e-003-2.552e-003-2.552e-003-4.128e-003-4.128e-003-2.552e-003转角位移2.986e-0031.806e-0031.806e-0032.986e-0032.986e-0031.806e-003节点号=5位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移2.792e-004-3.459e-005-3.459e-0052.792e-0042.792e-004-3.459e-005竖向位移-2.747e-003-1.712e-003-1.712e-003-2.747e-003-2.747e-003-1.712e-003转角位移2.516e-0031.546e-0031.546e-0032.516e-0032.516e-0031.546e-003节点号=6位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移2.364e-004-1.573e-005-1.573e-0052.364e-0042.364e-004-1.573e-005竖向位移-1.612e-003-1.012e-003-1.012e-003-1.612e-003-1.612e-003-1.012e-003转角位移2.003e-0031.249e-0031.249e-0032.003e-0032.003e-0031.249e-003节点号=7位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.845e-004-2.448e-006-2.448e-0061.845e-0041.845e-004-2.448e-006竖向位移-7.493e-004-4.726e-004-4.726e-004-7.493e-004-7.493e-004-4.726e-004转角位移1.425e-0038.993e-0048.993e-0041.425e-0031.425e-0038.993e-004节点号=8位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.200e-0042.894e-0062.894e-0061.200e-0041.200e-0042.894e-006竖向位移-1.961e-004-1.236e-004-1.236e-004-1.961e-004-1.961e-004-1.236e-004转角位移7.561e-0044.820e-0044.820e-0047.561e-0047.561e-0044.820e-004节点号=9位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移4.345e-0050.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向位移0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000转角位移2.119e-0060.000e+0000.000e+0000.000e+0000.000e+0000.000e+000承载能力极限状态荷载组合II内力结果:单元号=1,左节点号=1内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=1,右节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=2,左节点号=2130
内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=2,右节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=3,左节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=3,右节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=4,左节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=4,右节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=5,左节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=5,右节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=6,左节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000130
单元号=6,右节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=7,左节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=7,右节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=8,左节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=8,右节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=9,左节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=9,右节点号=10内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000正常使用极限状态荷载组合II内力结果:单元号=1,左节点号=1内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=1,右节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.954e-0018.954e-0018.954e-0018.954e-0018.954e-0018.954e-001剪力2.420e+0012.420e+0012.420e+0012.420e+0012.420e+0012.420e+001130
弯矩-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000单元号=2,左节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力9.196e-0019.196e-0019.196e-0019.196e-0019.196e-0019.196e-001剪力-2.420e+001-2.420e+001-2.420e+001-2.420e+001-2.420e+001-2.420e+001弯矩-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000单元号=2,右节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.514e+0001.514e+0001.514e+0001.514e+0001.514e+0001.514e+000剪力3.985e+0013.985e+0013.985e+0013.985e+0013.985e+0013.985e+001弯矩-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001单元号=3,左节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.474e+0001.474e+0001.474e+0001.474e+0001.474e+0001.474e+000剪力-3.985e+001-3.985e+001-3.985e+001-3.985e+001-3.985e+001-3.985e+001弯矩-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001单元号=3,右节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.080e+0002.080e+0002.080e+0002.080e+0002.080e+0002.080e+000剪力5.620e+0015.620e+0015.620e+0015.620e+0015.620e+0015.620e+001弯矩-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001单元号=4,左节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.136e+0002.136e+0002.136e+0002.136e+0002.136e+0002.136e+000剪力-5.620e+001-5.620e+001-5.620e+001-5.620e+001-5.620e+001-5.620e+001弯矩-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001单元号=4,右节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.784e+0002.784e+0002.784e+0002.784e+0002.784e+0002.784e+000剪力7.326e+0017.326e+0017.326e+0017.326e+0017.326e+0017.326e+001弯矩-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001单元号=5,左节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.711e+0002.711e+0002.711e+0002.711e+0002.711e+0002.711e+000剪力-7.326e+001-7.326e+001-7.326e+001-7.326e+001-7.326e+001-7.326e+001弯矩-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001单元号=5,右节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力4.714e+0004.714e+0004.714e+0004.714e+0004.714e+0004.714e+000剪力1.274e+0021.274e+0021.274e+0021.274e+0021.274e+0021.274e+002弯矩-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002单元号=6,左节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力4.841e+0004.841e+0004.841e+0004.841e+0004.841e+0004.841e+000剪力-1.274e+002-1.274e+002-1.274e+002-1.274e+002-1.274e+002-1.274e+002130
弯矩-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002单元号=6,右节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力5.419e+0005.419e+0005.419e+0005.419e+0005.419e+0005.419e+000剪力1.426e+0021.426e+0021.426e+0021.426e+0021.426e+0021.426e+002弯矩-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002单元号=7,左节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力7.865e+0007.865e+0007.865e+0007.865e+0007.865e+0007.865e+000剪力-2.126e+002-2.126e+002-2.126e+002-2.126e+002-2.126e+002-2.126e+002弯矩-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002单元号=7,右节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.454e+0008.454e+0008.454e+0008.454e+0008.454e+0008.454e+000剪力2.285e+0022.285e+0022.285e+0022.285e+0022.285e+0022.285e+002弯矩-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002单元号=8,左节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.682e+0008.682e+0008.682e+0008.682e+0008.682e+0008.682e+000剪力-2.285e+002-2.285e+002-2.285e+002-2.285e+002-2.285e+002-2.285e+002弯矩-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002单元号=8,右节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力9.313e+0009.313e+0009.313e+0009.313e+0009.313e+0009.313e+000剪力2.451e+0022.451e+0022.451e+0022.451e+0022.451e+0022.451e+002弯矩-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002单元号=9,左节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.193e-0133.193e-0133.193e-0133.193e-0133.193e-0133.193e-013剪力8.739e+0028.739e+0028.739e+0028.739e+0028.739e+0028.739e+002弯矩-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002单元号=9,右节点号=10内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.193e-0133.193e-0133.193e-0133.193e-0133.193e-0133.193e-013剪力-8.091e+002-8.091e+002-8.091e+002-8.091e+002-8.091e+002-8.091e+002弯矩-1.155e-014-1.155e-014-1.155e-014-1.155e-014-1.155e-014-1.155e-014正常使用极限状态荷载组合II位移结果:节点号=1位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.282e-003-1.310e-003-5.869e-0045.585e-004-1.165e-0048.806e-005竖向位移-7.350e-003-9.801e-003-3.530e-003-1.362e-002-1.360e-002-3.553e-003转角位移2.580e-0034.818e-0038.819e-0046.517e-0036.517e-0038.819e-004节点号=2位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.149e-003-1.110e-003-5.253e-0045.641e-004-3.593e-0057.468e-005130
竖向位移-6.022e-003-7.549e-003-3.026e-003-1.055e-002-1.053e-002-3.046e-003转角位移2.672e-0034.211e-0031.116e-0035.767e-0035.767e-0031.116e-003节点号=3位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.017e-003-9.225e-004-4.579e-0045.528e-0042.779e-0056.709e-005竖向位移-4.694e-003-5.596e-003-2.442e-003-7.848e-003-7.831e-003-2.459e-003转角位移2.586e-0033.622e-0031.208e-0035.001e-0035.001e-0031.208e-003节点号=4位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移8.825e-004-7.508e-004-3.888e-0045.205e-0047.049e-0056.123e-005竖向位移-3.444e-003-3.934e-003-1.841e-003-5.538e-003-5.524e-003-1.855e-003转角位移2.368e-0033.041e-0031.188e-0034.221e-0034.221e-0031.188e-003节点号=5位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移7.449e-004-5.910e-004-3.189e-0044.728e-0049.781e-0055.612e-005竖向位移-2.328e-003-2.561e-003-1.271e-003-3.619e-003-3.607e-003-1.282e-003转角位移2.056e-0032.467e-0031.086e-0033.437e-0033.437e-0031.086e-003节点号=6位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移6.012e-004-4.453e-0044.905e-0051.068e-0041.068e-0044.905e-005竖向位移-1.386e-003-1.473e-003-7.771e-004-2.082e-003-2.082e-003-7.771e-004转角位移1.677e-0031.901e-0039.221e-0042.656e-0032.656e-0039.221e-004节点号=7位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移4.516e-004-3.118e-0043.974e-0051.001e-0041.001e-0043.974e-005竖向位移-6.525e-004-6.717e-004-3.702e-004-9.540e-004-9.540e-004-3.702e-004转角位移1.217e-0031.316e-0036.909e-0041.842e-0031.842e-0036.909e-004节点号=8位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移2.931e-004-1.933e-0042.599e-0057.380e-0057.380e-0052.599e-005竖向位移-1.732e-004-1.724e-004-9.773e-005-2.478e-004-2.478e-004-9.773e-005转角位移6.542e-0046.858e-0043.801e-0049.599e-0049.599e-0043.801e-004节点号=9位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.184e-004-8.568e-0050.000e+0000.000e+000-1.068e-0050.000e+000竖向位移0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000转角位移2.119e-0061.063e-0050.000e+0000.000e+0001.063e-0050.000e+000承载能力极限状态荷载组合III内力结果:单元号=1,左节点号=1内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=1,右节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩130
轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=2,左节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=2,右节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=3,左节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=3,右节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=4,左节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=4,右节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=5,左节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=5,右节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=6,左节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩130
轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=6,右节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=7,左节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=7,右节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=8,左节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=8,右节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=9,左节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=9,右节点号=10内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000正常使用极限状态荷载组合III内力结果:单元号=1,左节点号=1内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000剪力0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000弯矩0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000单元号=1,右节点号=2130
内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.954e-0018.954e-0018.954e-0018.954e-0018.954e-0018.954e-001剪力2.420e+0012.420e+0012.420e+0012.420e+0012.420e+0012.420e+001弯矩-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000单元号=2,左节点号=2内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力9.196e-0019.196e-0019.196e-0019.196e-0019.196e-0019.196e-001剪力-2.420e+001-2.420e+001-2.420e+001-2.420e+001-2.420e+001-2.420e+001弯矩-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000-7.414e+000单元号=2,右节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.514e+0001.514e+0001.514e+0001.514e+0001.514e+0001.514e+000剪力3.985e+0013.985e+0013.985e+0013.985e+0013.985e+0013.985e+001弯矩-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001单元号=3,左节点号=3内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力1.474e+0001.474e+0001.474e+0001.474e+0001.474e+0001.474e+000剪力-3.985e+001-3.985e+001-3.985e+001-3.985e+001-3.985e+001-3.985e+001弯矩-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001-2.341e+001单元号=3,右节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.080e+0002.080e+0002.080e+0002.080e+0002.080e+0002.080e+000剪力5.620e+0015.620e+0015.620e+0015.620e+0015.620e+0015.620e+001弯矩-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001单元号=4,左节点号=4内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.136e+0002.136e+0002.136e+0002.136e+0002.136e+0002.136e+000剪力-5.620e+001-5.620e+001-5.620e+001-5.620e+001-5.620e+001-5.620e+001弯矩-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001-4.741e+001单元号=4,右节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.784e+0002.784e+0002.784e+0002.784e+0002.784e+0002.784e+000剪力7.326e+0017.326e+0017.326e+0017.326e+0017.326e+0017.326e+001弯矩-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001单元号=5,左节点号=5内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力2.711e+0002.711e+0002.711e+0002.711e+0002.711e+0002.711e+000剪力-7.326e+001-7.326e+001-7.326e+001-7.326e+001-7.326e+001-7.326e+001弯矩-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001-7.977e+001单元号=5,右节点号=6内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力4.714e+0004.714e+0004.714e+0004.714e+0004.714e+0004.714e+000剪力1.274e+0021.274e+0021.274e+0021.274e+0021.274e+0021.274e+002弯矩-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002单元号=6,左节点号=6130
内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力4.841e+0004.841e+0004.841e+0004.841e+0004.841e+0004.841e+000剪力-1.274e+002-1.274e+002-1.274e+002-1.274e+002-1.274e+002-1.274e+002弯矩-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002-1.245e+002单元号=6,右节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力5.419e+0005.419e+0005.419e+0005.419e+0005.419e+0005.419e+000剪力1.426e+0021.426e+0021.426e+0021.426e+0021.426e+0021.426e+002弯矩-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002单元号=7,左节点号=7内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力7.865e+0007.865e+0007.865e+0007.865e+0007.865e+0007.865e+000剪力-2.126e+002-2.126e+002-2.126e+002-2.126e+002-2.126e+002-2.126e+002弯矩-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002-1.920e+002单元号=7,右节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.454e+0008.454e+0008.454e+0008.454e+0008.454e+0008.454e+000剪力2.285e+0022.285e+0022.285e+0022.285e+0022.285e+0022.285e+002弯矩-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002单元号=8,左节点号=8内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力8.682e+0008.682e+0008.682e+0008.682e+0008.682e+0008.682e+000剪力-2.285e+002-2.285e+002-2.285e+002-2.285e+002-2.285e+002-2.285e+002弯矩-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002-3.023e+002单元号=8,右节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力9.313e+0009.313e+0009.313e+0009.313e+0009.313e+0009.313e+000剪力2.451e+0022.451e+0022.451e+0022.451e+0022.451e+0022.451e+002弯矩-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002单元号=9,左节点号=9内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.193e-0133.193e-0133.193e-0133.193e-0133.193e-0133.193e-013剪力8.739e+0028.739e+0028.739e+0028.739e+0028.739e+0028.739e+002弯矩-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002-4.207e+002单元号=9,右节点号=10内力性质最大轴力最小轴力最大剪力最小剪力最大弯矩最小弯矩轴力3.193e-0133.193e-0133.193e-0133.193e-0133.193e-0133.193e-013剪力-8.091e+002-8.091e+002-8.091e+002-8.091e+002-8.091e+002-8.091e+002弯矩-1.155e-014-1.155e-014-1.155e-014-1.155e-014-1.155e-014-1.155e-014正常使用极限状态荷载组合III位移结果:节点号=1位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移3.657e-004-1.530e-004-1.530e-0043.657e-0043.657e-004-1.530e-004竖向位移-9.418e-003-5.643e-003-5.643e-003-9.418e-003-9.418e-003-5.643e-003转角位移3.893e-0032.194e-0032.194e-0033.893e-0033.893e-0032.194e-003130
节点号=2位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移3.539e-004-1.202e-004-1.202e-0043.539e-0043.539e-004-1.202e-004竖向位移-7.510e-003-4.554e-003-4.554e-003-7.510e-003-7.510e-003-4.554e-003转角位移3.704e-0032.147e-0032.147e-0033.704e-0033.704e-0032.147e-003节点号=3位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移3.375e-004-8.778e-005-8.778e-0053.375e-0043.375e-004-8.778e-005竖向位移-5.729e-003-3.510e-003-3.510e-003-5.729e-003-5.729e-003-3.510e-003转角位移3.391e-0032.013e-0032.013e-0033.391e-0033.391e-0032.013e-003节点号=4位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移3.119e-004-5.945e-005-5.945e-0053.119e-0043.119e-004-5.945e-005竖向位移-4.128e-003-2.552e-003-2.552e-003-4.128e-003-4.128e-003-2.552e-003转角位移2.986e-0031.806e-0031.806e-0032.986e-0032.986e-0031.806e-003节点号=5位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移2.792e-004-3.459e-005-3.459e-0052.792e-0042.792e-004-3.459e-005竖向位移-2.747e-003-1.712e-003-1.712e-003-2.747e-003-2.747e-003-1.712e-003转角位移2.516e-0031.546e-0031.546e-0032.516e-0032.516e-0031.546e-003节点号=6位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移2.364e-004-1.573e-005-1.573e-0052.364e-0042.364e-004-1.573e-005竖向位移-1.612e-003-1.012e-003-1.012e-003-1.612e-003-1.612e-003-1.012e-003转角位移2.003e-0031.249e-0031.249e-0032.003e-0032.003e-0031.249e-003节点号=7位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.845e-004-2.448e-006-2.448e-0061.845e-0041.845e-004-2.448e-006竖向位移-7.493e-004-4.726e-004-4.726e-004-7.493e-004-7.493e-004-4.726e-004转角位移1.425e-0038.993e-0048.993e-0041.425e-0031.425e-0038.993e-004节点号=8位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移1.200e-0042.894e-0062.894e-0061.200e-0041.200e-0042.894e-006竖向位移-1.961e-004-1.236e-004-1.236e-004-1.961e-004-1.961e-004-1.236e-004转角位移7.561e-0044.820e-0044.820e-0047.561e-0047.561e-0044.820e-004节点号=9位移性质最大水平最小水平最大竖向最小竖向最大转角最小转角水平位移4.345e-0050.000e+0000.000e+0000.000e+0000.000e+0000.000e+000竖向位移0.000e+0000.000e+0000.000e+0000.000e+0000.000e+0000.000e+000转角位移2.119e-0060.000e+0000.000e+0000.000e+0000.000e+0000.000e+000********************************************************************************指定单元截面应力输出********************************************************************************第1施工阶段应力结果130
阶段累计应力:主截面:单元号左上缘左下缘右上缘右下缘11.26e-013000.62200.6201.52301.5202.43402.4303.29503.2904.24604.2405.48705.4807.37807.3708.85901.3303.64e-017阶段永久载应力:主截面:单元号左上缘左下缘右上缘右下缘11.28e-013000.62200.6201.52301.5202.43402.4303.29503.2904.24604.2405.48705.4807.37807.3708.85901.3308.4e-017正常使用阶段应力计算结果主截面:结构重力应力结果单元号左上缘左下缘右上缘右下缘11.26e-013000.62200.6201.52301.5202.43402.4303.29503.2904.24604.2405.48705.4807.37807.3708.85901.3303.64e-017使用阶段荷载组合1应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉110000001200000022000.620.620.62-0.0948130
23000.4790.4790.479-0.077633001.521.521.52-0.12734001.21.21.2-0.10744002.432.432.43-0.15145001.961.961.96-0.14555003.293.293.29-0.18956002.722.722.72-0.16966004.244.244.24-0.29467003.563.563.56-0.26577005.485.485.48-0.44278004.684.684.68-0.40288007.377.377.37-0.43289006.366.366.36-0.39599001.331.331.33-0.344910001.331.331.33-0.344使用阶段荷载组合2应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉110000001200000022000.620.620.62-0.094823000.4790.4790.479-0.077633001.521.521.52-0.12734001.21.21.2-0.10744002.432.432.43-0.15145001.961.961.96-0.14555003.293.293.29-0.18956002.722.722.72-0.16966004.244.244.24-0.29467003.563.563.56-0.26577005.485.485.48-0.44278004.684.684.68-0.40288007.377.377.37-0.43289006.366.366.36-0.39599001.331.331.33-0.344910001.331.331.33-0.344使用阶段荷载组合3应力:主截面:单元号节点号上缘最大上缘最小下缘最大下缘最小最大主压最大主拉110000001200000022000.620.620.62-0.094823000.4790.4790.479-0.077633001.521.521.52-0.12734001.21.21.2-0.107130
44002.432.432.43-0.15145001.961.961.96-0.14555003.293.293.29-0.18956002.722.722.72-0.16966004.244.244.24-0.29467003.563.563.56-0.26577005.485.485.48-0.44278004.684.684.68-0.40288007.377.377.37-0.43289006.366.366.36-0.39599001.331.331.33-0.344910001.331.331.33-0.344********************************************************************************指定单元截面强度验算输出********************************************************************************1#单元左截面:荷载组合I类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.527e+002最小轴力下拉受弯0.000e+0000.000e+0001.527e+002最大弯矩下拉受弯0.000e+0000.000e+0001.527e+002最小弯矩下拉受弯0.000e+0000.000e+0001.527e+002荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.527e+002最小轴力下拉受弯0.000e+0000.000e+0001.527e+002最大弯矩下拉受弯0.000e+0000.000e+0001.527e+002最小弯矩下拉受弯0.000e+0000.000e+0001.527e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.527e+002最小轴力下拉受弯0.000e+0000.000e+0001.527e+002最大弯矩下拉受弯0.000e+0000.000e+0001.527e+002最小弯矩下拉受弯0.000e+0000.000e+0001.527e+0021#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉偏压1.075e+000-8.897e+0005.370e+001最小轴力上拉受弯8.954e-001-7.414e+000-4.298e+002最大弯矩上拉受弯8.954e-001-7.414e+000-4.298e+002最小弯矩上拉偏压1.075e+000-8.897e+0005.370e+001荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.575e+002130
最小轴力下拉受弯0.000e+0000.000e+0001.575e+002最大弯矩下拉受弯0.000e+0000.000e+0001.575e+002最小弯矩下拉受弯0.000e+0000.000e+0001.575e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.575e+002最小轴力下拉受弯0.000e+0000.000e+0001.575e+002最大弯矩下拉受弯0.000e+0000.000e+0001.575e+002最小弯矩下拉受弯0.000e+0000.000e+0001.575e+0022#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉偏压1.104e+000-8.897e+0005.370e+001最小轴力上拉受弯9.196e-001-7.414e+000-4.298e+002最大弯矩上拉受弯9.196e-001-7.414e+000-4.298e+002最小弯矩上拉偏压1.104e+000-8.897e+0005.370e+001荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.575e+002最小轴力下拉受弯0.000e+0000.000e+0001.575e+002最大弯矩下拉受弯0.000e+0000.000e+0001.575e+002最小弯矩下拉受弯0.000e+0000.000e+0001.575e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.575e+002最小轴力下拉受弯0.000e+0000.000e+0001.575e+002最大弯矩下拉受弯0.000e+0000.000e+0001.575e+002最小弯矩下拉受弯0.000e+0000.000e+0001.575e+0022#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉偏压1.817e+000-2.809e+0013.662e+001最小轴力上拉偏压1.514e+000-2.341e+0013.662e+001最大弯矩上拉偏压1.514e+000-2.341e+0013.662e+001最小弯矩上拉偏压1.817e+000-2.809e+0013.662e+001荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.661e+002最小轴力下拉受弯0.000e+0000.000e+0001.661e+002最大弯矩下拉受弯0.000e+0000.000e+0001.661e+002最小弯矩下拉受弯0.000e+0000.000e+0001.661e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.661e+002最小轴力下拉受弯0.000e+0000.000e+0001.661e+002130
最大弯矩下拉受弯0.000e+0000.000e+0001.661e+002最小弯矩下拉受弯0.000e+0000.000e+0001.661e+0023#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉偏压1.769e+000-2.809e+0013.662e+001最小轴力上拉偏压1.474e+000-2.341e+0013.662e+001最大弯矩上拉偏压1.474e+000-2.341e+0013.662e+001最小弯矩上拉偏压1.769e+000-2.809e+0013.662e+001荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.661e+002最小轴力下拉受弯0.000e+0000.000e+0001.661e+002最大弯矩下拉受弯0.000e+0000.000e+0001.661e+002最小弯矩下拉受弯0.000e+0000.000e+0001.661e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.661e+002最小轴力下拉受弯0.000e+0000.000e+0001.661e+002最大弯矩下拉受弯0.000e+0000.000e+0001.661e+002最小弯矩下拉受弯0.000e+0000.000e+0001.661e+0023#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉受弯2.495e+000-5.689e+001-6.619e+002最小轴力上拉受弯2.080e+000-4.741e+001-6.619e+002最大弯矩上拉受弯2.080e+000-4.741e+001-6.619e+002最小弯矩上拉受弯2.495e+000-5.689e+001-6.619e+002荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.532e+002最小轴力下拉受弯0.000e+0000.000e+0001.532e+002最大弯矩下拉受弯0.000e+0000.000e+0001.532e+002最小弯矩下拉受弯0.000e+0000.000e+0001.532e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.532e+002最小轴力下拉受弯0.000e+0000.000e+0001.532e+002最大弯矩下拉受弯0.000e+0000.000e+0001.532e+002最小弯矩下拉受弯0.000e+0000.000e+0001.532e+0024#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉受弯2.563e+000-5.689e+001-6.619e+002最小轴力上拉受弯2.136e+000-4.741e+001-6.619e+002130
最大弯矩上拉受弯2.136e+000-4.741e+001-6.619e+002最小弯矩上拉受弯2.563e+000-5.689e+001-6.619e+002荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.532e+002最小轴力下拉受弯0.000e+0000.000e+0001.532e+002最大弯矩下拉受弯0.000e+0000.000e+0001.532e+002最小弯矩下拉受弯0.000e+0000.000e+0001.532e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.532e+002最小轴力下拉受弯0.000e+0000.000e+0001.532e+002最大弯矩下拉受弯0.000e+0000.000e+0001.532e+002最小弯矩下拉受弯0.000e+0000.000e+0001.532e+0024#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉受弯3.341e+000-9.572e+001-8.162e+002最小轴力上拉受弯2.784e+000-7.977e+001-8.162e+002最大弯矩上拉受弯2.784e+000-7.977e+001-8.162e+002最小弯矩上拉受弯3.341e+000-9.572e+001-8.162e+002荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.543e+002最小轴力下拉受弯0.000e+0000.000e+0001.543e+002最大弯矩下拉受弯0.000e+0000.000e+0001.543e+002最小弯矩下拉受弯0.000e+0000.000e+0001.543e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.543e+002最小轴力下拉受弯0.000e+0000.000e+0001.543e+002最大弯矩下拉受弯0.000e+0000.000e+0001.543e+002最小弯矩下拉受弯0.000e+0000.000e+0001.543e+0025#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉受弯3.253e+000-9.572e+001-8.162e+002最小轴力上拉受弯2.711e+000-7.977e+001-8.162e+002最大弯矩上拉受弯2.711e+000-7.977e+001-8.162e+002最小弯矩上拉受弯3.253e+000-9.572e+001-8.162e+002荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.543e+002最小轴力下拉受弯0.000e+0000.000e+0001.543e+002最大弯矩下拉受弯0.000e+0000.000e+0001.543e+002130
最小弯矩下拉受弯0.000e+0000.000e+0001.543e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.543e+002最小轴力下拉受弯0.000e+0000.000e+0001.543e+002最大弯矩下拉受弯0.000e+0000.000e+0001.543e+002最小弯矩下拉受弯0.000e+0000.000e+0001.543e+0025#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉受弯5.656e+000-1.494e+002-9.616e+002最小轴力上拉受弯4.714e+000-1.245e+002-9.616e+002最大弯矩上拉受弯4.714e+000-1.245e+002-9.616e+002最小弯矩上拉受弯5.656e+000-1.494e+002-9.616e+002荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.535e+002最小轴力下拉受弯0.000e+0000.000e+0001.535e+002最大弯矩下拉受弯0.000e+0000.000e+0001.535e+002最小弯矩下拉受弯0.000e+0000.000e+0001.535e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.535e+002最小轴力下拉受弯0.000e+0000.000e+0001.535e+002最大弯矩下拉受弯0.000e+0000.000e+0001.535e+002最小弯矩下拉受弯0.000e+0000.000e+0001.535e+0026#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉受弯5.809e+000-1.494e+002-9.616e+002最小轴力上拉受弯4.841e+000-1.245e+002-9.616e+002最大弯矩上拉受弯4.841e+000-1.245e+002-9.616e+002最小弯矩上拉受弯5.809e+000-1.494e+002-9.616e+002荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.535e+002最小轴力下拉受弯0.000e+0000.000e+0001.535e+002最大弯矩下拉受弯0.000e+0000.000e+0001.535e+002最小弯矩下拉受弯0.000e+0000.000e+0001.535e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.535e+002最小轴力下拉受弯0.000e+0000.000e+0001.535e+002最大弯矩下拉受弯0.000e+0000.000e+0001.535e+002最小弯矩下拉受弯0.000e+0000.000e+0001.535e+002130
6#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉受弯6.503e+000-2.304e+002-1.102e+003最小轴力上拉受弯5.419e+000-1.920e+002-1.102e+003最大弯矩上拉受弯5.419e+000-1.920e+002-1.102e+003最小弯矩上拉受弯6.503e+000-2.304e+002-1.102e+003荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.630e+002最小轴力下拉受弯0.000e+0000.000e+0001.630e+002最大弯矩下拉受弯0.000e+0000.000e+0001.630e+002最小弯矩下拉受弯0.000e+0000.000e+0001.630e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.630e+002最小轴力下拉受弯0.000e+0000.000e+0001.630e+002最大弯矩下拉受弯0.000e+0000.000e+0001.630e+002最小弯矩下拉受弯0.000e+0000.000e+0001.630e+0027#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉受弯9.438e+000-2.304e+002-1.102e+003最小轴力上拉受弯7.865e+000-1.920e+002-1.102e+003最大弯矩上拉受弯7.865e+000-1.920e+002-1.102e+003最小弯矩上拉受弯9.438e+000-2.304e+002-1.102e+003荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.630e+002最小轴力下拉受弯0.000e+0000.000e+0001.630e+002最大弯矩下拉受弯0.000e+0000.000e+0001.630e+002最小弯矩下拉受弯0.000e+0000.000e+0001.630e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.630e+002最小轴力下拉受弯0.000e+0000.000e+0001.630e+002最大弯矩下拉受弯0.000e+0000.000e+0001.630e+002最小弯矩下拉受弯0.000e+0000.000e+0001.630e+0027#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉受弯1.014e+001-3.628e+002-1.240e+003最小轴力上拉受弯8.454e+000-3.023e+002-1.240e+003最大弯矩上拉受弯8.454e+000-3.023e+002-1.240e+003最小弯矩上拉受弯1.014e+001-3.628e+002-1.240e+003130
荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.561e+002最小轴力下拉受弯0.000e+0000.000e+0001.561e+002最大弯矩下拉受弯0.000e+0000.000e+0001.561e+002最小弯矩下拉受弯0.000e+0000.000e+0001.561e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.561e+002最小轴力下拉受弯0.000e+0000.000e+0001.561e+002最大弯矩下拉受弯0.000e+0000.000e+0001.561e+002最小弯矩下拉受弯0.000e+0000.000e+0001.561e+0028#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉受弯1.042e+001-3.628e+002-1.240e+003最小轴力上拉受弯8.682e+000-3.023e+002-1.240e+003最大弯矩上拉受弯8.682e+000-3.023e+002-1.240e+003最小弯矩上拉受弯1.042e+001-3.628e+002-1.240e+003荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.561e+002最小轴力下拉受弯0.000e+0000.000e+0001.561e+002最大弯矩下拉受弯0.000e+0000.000e+0001.561e+002最小弯矩下拉受弯0.000e+0000.000e+0001.561e+002荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.561e+002最小轴力下拉受弯0.000e+0000.000e+0001.561e+002最大弯矩下拉受弯0.000e+0000.000e+0001.561e+002最小弯矩下拉受弯0.000e+0000.000e+0001.561e+0028#单元右截面:荷载组合I类型性质NjMjR最大轴力上拉受弯1.118e+001-5.049e+002-1.381e+003最小轴力上拉受弯9.313e+000-4.207e+002-1.381e+003最大弯矩上拉受弯9.313e+000-4.207e+002-1.381e+003最小弯矩上拉受弯1.118e+001-5.049e+002-1.381e+003荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.685e+002最小轴力下拉受弯0.000e+0000.000e+0001.685e+002最大弯矩下拉受弯0.000e+0000.000e+0001.685e+002最小弯矩下拉受弯0.000e+0000.000e+0001.685e+002荷载组合III130
类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0001.685e+002最小轴力下拉受弯0.000e+0000.000e+0001.685e+002最大弯矩下拉受弯0.000e+0000.000e+0001.685e+002最小弯矩下拉受弯0.000e+0000.000e+0001.685e+0029#单元左截面:荷载组合I类型性质NjMjR最大轴力上拉受弯3.832e-013-5.049e+002-2.303e+003最小轴力上拉受弯3.193e-013-4.207e+002-2.303e+003最大弯矩上拉受弯3.193e-013-4.207e+002-2.303e+003最小弯矩上拉受弯3.832e-013-5.049e+002-2.303e+003荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0002.096e+003最小轴力下拉受弯0.000e+0000.000e+0002.096e+003最大弯矩下拉受弯0.000e+0000.000e+0002.096e+003最小弯矩下拉受弯0.000e+0000.000e+0002.096e+003荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0002.096e+003最小轴力下拉受弯0.000e+0000.000e+0002.096e+003最大弯矩下拉受弯0.000e+0000.000e+0002.096e+003最小弯矩下拉受弯0.000e+0000.000e+0002.096e+0039#单元右截面:荷载组合I类型性质NjMjR最大轴力下拉受弯3.832e-013-1.386e-0142.096e+003最小轴力下拉受弯3.193e-013-1.155e-0142.096e+003最大弯矩下拉受弯3.193e-013-1.155e-0142.096e+003最小弯矩下拉受弯3.832e-013-1.386e-0142.096e+003荷载组合II类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0002.096e+003最小轴力下拉受弯0.000e+0000.000e+0002.096e+003最大弯矩下拉受弯0.000e+0000.000e+0002.096e+003最小弯矩下拉受弯0.000e+0000.000e+0002.096e+003荷载组合III类型性质NjMjR最大轴力下拉受弯0.000e+0000.000e+0002.096e+003最小轴力下拉受弯0.000e+0000.000e+0002.096e+003最大弯矩下拉受弯0.000e+0000.000e+0002.096e+003最小弯矩下拉受弯0.000e+0000.000e+0002.096e+003********************************************************************************130
指定单元截面裂缝宽度输出********************************************************************************单元号组合类型左上缘左下缘右上缘右下缘1组合I000.0040201组合II000.0040201组合III000.0040202组合I0.0040200.0083102组合II0.0040200.0083102组合III0.0040200.0083103组合I0.0083100.018803组合II0.0083100.018803组合III0.0083100.018804组合I0.018800.022104组合II0.018800.022104组合III0.018800.022105组合I0.022100.030505组合II0.022100.030505组合III0.022100.030506组合I0.030500.041906组合II0.030500.041906组合III0.030500.041907组合I0.041900.059807组合II0.041900.059807组合III0.041900.059808组合I0.059800.075808组合II0.059800.075808组合III0.059800.075809组合I0.073801.35e-01809组合II0.073801.35e-01809组合III0.073801.35e-01802、悬臂验算主要结论结构极限承载力均满足规范要求,短期效应组合和长期效应组合正截面抗裂验算均满足普通钢筋混凝土受弯构件的要求。裂缝最大宽度为0.0758mm<0.2mm,满足规范要求。综上所述,各截面应力均满足规范限值。九、齿块计算130
l崩裂钢筋A1A1==实际布筋A1′=3.14×0.008×0.008×8=0.0016>A1满足要求F—钢筋的锚固力Z—自崩裂钢筋重心至钢束与底板顶面相交点之间的水平距离a—钢束的弯起角d—锚固力作用点距底板顶面的距离[σg]—钢筋的容许应力l径向推力钢筋A3A3==实际布筋A3′=3.14×0.008×0.008×8=0.0032>A3满足要求F—钢筋的锚固力R—钢束的曲率半径a—弯曲半径中心角,以弧度计l中间钢筋A2A2==实际布筋A2′=3.14×0.008×0.008×28=0.0056>A2满足要求。十、栏杆计算书130
l永久作用效应扶手自重NG1=2×0.15×0.15×3.75×26=4.36KN栏杆自重NG2=0.15×0.15×0.8×26=0.498KN栏杆NG3=22×0.0.0028=0.06KN130
栏杆柱根部截面上永久作用产生的总轴向力NG=NG1+NG2+NG3=4.39+0.498+0.06=4.948l荷载效应按《桥规》4.3.5条,计算人行道栏杆荷载效应时,作用在栏杆顶上的水平推力标准值取0.75KN/m,作用在栏杆扶手的竖向力标准值取1.0KN/m。由于扶手两边对称,作用于扶手上的竖向力在栏杆柱根部截面产生轴向力Np,水平推力在栏杆的根部截面形成剪力Vp,弯矩Mp。其大小为:Np=1×3.75=3.75KNVp=0.75×3.75=2.81KNMp=0.75×3.75×=2.88KN•m1、栏杆柱根部截面Ⅰ—Ⅰ上按承载能力极限状态基本组合的效应组合设计值为:Nd=1.2×4.948+1.4×3.75=11.19KNVd=1.4×2.81=3.93KNMd=1.4×2.88=4.032KN•m2、栏杆柱的钢筋布置栏杆采用C25砼,栏杆柱受力筋采用R235普通钢筋Φ12.箍筋采用φ8栏杆柱承载能力复核栏杆柱是一个偏心受压的构件全部纵向钢筋配筋率为ρ==0.02>0.005侧钢筋配筋率为ρˊ==0.02>0.005按《桥规》D62要求先按偏心受压构件计算L/h=800/150=5.3>5,考虑偏心矩增大系数130
ξ1=0.2+2.7e0/h0=0.27×=7.98取ξ1=1ξ2=1.15-0.01×e0/h=1.15-0.01×=1.09取ξ2=1η=[1+(L0/h)2ξ1ξ2]=[1+×(800/150)2×1×1]=1由所有的力对轴向里Np作用点,取矩的平衡条件得:fcdb(es-h0+)=σsAses-fsdˊAsˊesˊ取σs=fsde0===360.3mmes=es+-as=360.3+-25=410.3mmesˊ=ηe0-+as=1×360.3-+25=310.3mmfcdbx(es-h0+)=σsAses-fsdˊAsˊesˊfcd=11.5Mpa取σs=fsd=280Mpah0=150-25=125mmAs=2×=226.08mm211.5×150××[410.3-125+]=280×226.08×410.3-280×226.08×310.3整理得:0.86252+492.14-6330.2=0=12.56mm<ξbh0=0.56×125=70所以栏杆柱为大偏心受压构件<2as=2×25=70说明受压钢筋离中性轴太近,构件破坏时受压钢筋的应力达不到强度设计值.构件正截面承载力按下列公式计算:r0Ndesˊ≤fsdAs(hs-asˊ)1×11.19×310.3≤280×226.08×(125-25)3472.26≤6330计算结果表明,截面抗弯承载力是足够的。130'